Loading...
Schwan's Distribution Center CZC 06-218:='t Le CITY OF- PY1G1 CEIVE IDAHO yF JAN 0 p 2667 � 7Retisu�V^"�`� Sso3 City of Meridian City Clerk office CERTIFICATE OF ZONING COMPLIANCE* Date:_ January 5, 2007 Project Natne/Number: Schwan's Distribution Center — CZC-06-218 Owner: Schwan's Consumer Brands North AmericanInc. Site Address: 1260 E. Watertower Lane (Parcel #R59011700220) (Lot 10 Block 1 Murdoch Sub. 2) Proposed Use: 7,510 square foot office/warehouse/distribution facility for Schwan's (Flex space) Zoning: C -G (General Retail and Service Commercial District) Comments: Conditions of Approval: Project is subject to all current City of Meridian ordinances and conditions of approval of the Murdoch Sub. No. 2 rezone (RZ-02-004), plat, all other conditions of approval associated with this ,site, if applicable). The issuance of this CZC does not release the applicant "from any previous requirements of the other permits issued for this site. NOTE: This is not a Building Permit. Prior to any construction, you shall contact the Building -Department at (208) 887-2211 to verifv if anv additional hermits and/or inspections will be required by the Building De artment. - Flex Space: Flex Space is defined in UDC 11-1A-1, as "the use of a site for warehousing, offices, and/or retail showroom. Flexibility in use of the interior spaces and low -scale, attractive exterior appearance characterize flex buildings." Per UDC 11-4-3.17, "Retail use shall not exceed 25% of leasable area in any tenant space." The proposed uses on the subject site must comply with the afore -mentioned definition and terms of Flex Space. Landscaping_ The Landscape Plan prepared by Good Earth Landscape, on 12-15-06, labeled Sheet L1.1, is approved (stamped "Approved" on 1-5-07 by the Meridian Planning Department) with the following changes/notes: 1)_ Provide landscaping around the condensing units, gas meter; etc. on•the east side of the building in accordance with UDC 11-3A-12 Outdoor Service & Equipment Areas so that the visual and acoustic impacts of these functions are fully contained and out of view from adjacent properties and public streets. 2) Provide landscaping within the landscape buffers adjacent to paved vehicular use areas at the east and northwest boundaries of the property in accordance with UDC 11-3B-SC1. Install 1 tree per 35 lineal feet as shown and shrubs, lawn, or other vegetative groundcover. Other than the above-mentioned changes, the approved landscape plan is not to be altered without prior written approval of the Planning Department. No field changes to landscape plan permitted; prior written approval of all material changes is required. Prior to final inspection and sign off for this project, a written certificate of completion shall be submitted to the Planning Department, prepared by a landscape architect, landscape designer or qualified nurseryman responsible for the landscape plan upon completion of the landscape installation. The Certificate of Completion shall verify that all landscape improvements, including plant materials and sprinkler installation, are in substantial compliance with the approved landscape plan. Site Plan: The Site Plan prepared by CTA Architects Engineers, on 12-15-06, labeled Sheet G201, is approved (stamped "Approved" on 1-5-07 by the Meridian Planning Department) with the following changes (see redline changes on site plan): 1) Provide a minimum 1 -space bicycle rack on this site in accordance with UDC 11 -3C -5C & 11- 3C -6G. 2) When a bumper overhangs onto a sidewalk or landscape area, the parking stall dimensions may be reduced two feet (2') in length if two feet W) is added to the width of the sidewalk or landscaped area planted in around cover. Increase the width of the sidewalk along the west side of the building adjacent to parking, to 7 -feet wide. Except for the changes mentioned above, the approved site plan is not to be altered without prior written approval of the Planning Department. Elevations: The Elevations prepared by CTA Architects Engineers (Sheet A201, dated 12-15-06) are approved with no changes from the Planning Department. Irrigation: An underground, pressurized irrigation system must be installed to all landscape areas per the approved specifications and in accordance with UDC 11-3A-15. Protection of Existing Trees: Any existing trees on site must be protected or mitigated for in accordance with the Tree Preservation section of the City's Landscape Ordinance. Per UDC 11-3B-10, coordinate with the Parks Department Arborist (Elroy Huff, 888-3579) for approval of protection/relocation measures for the existing trees prior to construction. Any severely damaged tree must be replaced in compliance with UDC 11- 3B -10-C.5. Parking: The proposed parking areas shall be paved and striped in accordance with UDC 11-313. Project engineer/architect shall certify that the number and size of handicap -accessible spaces conforms to the Americans with Disabilities Act (ADA). Handicap accessible stalls must have signage in accordance per ADA and signed accessible. See redline parking changes on the site plan. Curbing: Per UDC 11 -3B -5I, all landscape areas adjacent to driveways, parking lots, or other vehicle use areas, must be protected by curbing, wheel stops, or other approved protective devices. Curbing may be cut to allow for storm water runoff. Sidewalks: All sidewalks shall be constructed in accordance with 11-3A-17. Sidewalks shall be constructed prior to occupancy. Drainage: Storm water drainage swales shall not have a slope steeper than 3:1, shall be fully vegetated, and shall be designed in compliance with UDC 11-3B-11 and UDC 11-3A-18. Li tin : Lighting shall not cause glare or impact the traveling public or neighboring development and comply with lighting standards as defined in UDC 11-3A-11. Signage: No signs are approved with this CZC. All business signs will require a separate sign permit in compliance with UDC 11-3D. Trash Enclosure: All dumpster(s) must be screened in accordance with UDC -11-3A-12. Trash enclosures must be built in the location and to the size approved by SSC. Handicap -Accessibility: The structure, site improvements and parking areas must be in compliance with all federal handicap -accessibility requirements. ACHD Acceptance: All impact fees, if any, shall be paid prior to the issuance of a building permit. If any changes must be made to the site plan to accommodate the ACRD requirements, a new site plan shall be submitted to the City of Meridian Planning staff for approval prior to the issuance of a building permit. Certificate of Occupancy: All required improvements must be complete prior to obtaining a Certificate of Occupancy. All changes in occupancy need to comply with the requirements of the Building Department. It is unlawful to use or occupy any building or structure until the Building Official has issued a certificate of occupancy. A certificate of occupancy or temporary certificate of occupancy is obtained from the Building Department (208) 887-2211 after inspections are complete and the field inspection record is returned to the Building Department. Plan Modifications: Except for the changes mentioned above, the approved Site Plan, Landscape Plan, and Elevations, stamped "Approved" on 1-5-07, are not to be altered without prior written approval ofthe Planning Department. No significant field changes to the site or landscape plans are permitted; prior written approval of all changes is required. Sonya Vatters . Associate City Planner *This letter does not indicate compliance with requirements of other departments/agencies, including, but not limited to, Ada County Highway District, Central District Health Department, affected irrigation district(s), Meridian Sewer, Water, Building or Fire Departments, Sanitary Services Co., etc. This letter shall expire one (1) year from the date of issuance if work has not begun. Planning Department 11STRATIVE REVIEW APPLICATION VU ,CIE L Type of Review Requested (check all that apply) ❑ Accessory use ❑ Alternative Compliance ❑ Certificate of Zoning Compliance ❑ Conditional Use Permit Minor Modification ❑ Design Review ❑ Private Street ❑ Property Boundary Adjustment ❑ Shoit Plat ❑ Temporary Use Certificate of Zoning Compliance ❑ Time Extension (Director) ❑ Vacation ❑ Other �r Fie�S II ����Date�'comp�ete signed annex1+ r"�1� k, fr.�` sk 'Gi FiC Ogg,;dl4a at Applicant Information Applicant name: Jeffrey King Phone: (208) 947-2810 Applicant address: 1185 Grove Street Boise, Id Zip: 83702 Applicant's interest in property: ❑ Own ❑ Rent ❑ Optioned 13 Other Agent Owner name: Schwan's Consumer Brands North America, INC. Phone: (507) 537-8274 Owner address: 115 West college Drive Marshall, Mn Zip: 56258 Agent name (e.g., architect, engineer, developer, representative): Jeffrey King Firm name: CTA Architect Engineers Phone: (208) 947-2810 Address: 1185 Grove Street Boise, Id Zip: 83702 Primary contact is: ❑ Applicant ❑ Owner ®'Agent ❑ Other Contact name: Jeffrey King Phone: (208) 947-2810 E-mail: leffking(-ctagroup.com Fax: (208) 343-3531 ect Property Information , 51 b Location/street address 026)East Watertower Meridi, Assessor's parcel number(s): R -5901 -17 -00220 -Lot 10 Township, range, section: 3 North, 1 East, 18 Total acreage: .82 Acres Current land use: Bare Lot Current zoning district: CG 660 E. Watertower Lane, Smite 202 • Meridian, Idaho 83642 Phone: (208) 884-5533 • Facsimile: (208) 888-6854 • Website: www.meridiancity.org 1 (Rev. 9121106) Project Description Project/subdivision name: Schwan's Consumer Brands Warehouse & Distribution Facility General description of proposed project/request: New Commercial'Office / Warehouse Building Proposed zoning district(s): CG Acres of each zone proposed: .82 Acres Type of use proposed (check all that apply): ❑ Residential 129 Commercial ❑ Office ❑ Industrial ❑ Other Amenities provided with this development (if applicable): Who will own & maintain the pressurized irrigation system in this development? Which irrigation district does this property lie within? Nampa Meridian Irrigation District Primary irrigation source: Pressurized Irrigation Secondary: Square footage of landscaped areas to be irrigated (if primary or secondary point of connection is City water): Residential Project Summary (if applicable) Number of residential units: Number of building lots: Number of common and/or other lots: Proposed number of dwelling units (for multi -family developments only): 1 Bedroom: 2 or more Bedrooms: Minimum square footage of structure(s) (excl. garage): Proposed building height: Minimum property size (s.f): Average property size (s.f.): Gross density (DU/acre-total land): Net density (DU/acre-excluding roads & alleys): Percentage of open space provided: Acreage of open space: Percentage of useable open space: (See Chapter 3, Article G, for qualified open space) Type of open space provided in acres (i.e., landscaping, public, common, etc): Type of dwelling(s) proposed: ❑ Single-family ❑ Townhomes ❑ Duplexes ❑ Multi -family Non-residential Project Summary (if applicable) Number of building lots:1 Other lots: Gross floor area proposed: 7,510 Square Feet Existing (if applicable): Hours of operation (days and hours): 6 A.M. - 6 P.M. Building height: 24'-0" Percentage of site/project devoted to the following: Landscaping: 25% Building: 25% Paving: 50% Total number of employees: 8 Maximum number of employees at any one time: 12 Number and ages of students/children (if applicable): N/A Seating capacity: N/A Total number of parking1paces provided: 16 Number of compact spaces provided: 0 Authorization Print applicant name: I 1..,... Com.. Applicant signature: Date: 660 E. Watertowe L�.888-6854 02 • Meridian, Idaho 83642 Phone: 4JJ884-5%533 • Facys' • Website: www.meridiancity.org December 19, 2006 City of Meridian Planning & Zoning Department 660 E. Watertower Lane, Suite 202 Meridian, Idaho 83642 RE: Schwan's Consumer Brands Warehouse and Distribution Facility 1260 E. Watertown St. Meridian, Idaho 83642 Dear Sir or Madam: As an authorized agent of The Schwan Food Company, CTA Architects Engineers is herby submitting Construction Documents for a 7,510 sq. ft. office/warehouse/distribution facility for Schwan's Consumer Brands Division. The building is to be constructed on lot 10, Block 1 in the Murdoch Subdivision No. 2. Both lots 9 & 10 are identically zoned and owned by The Schwan Food Company. The project site abuts commercial properties on three sides and the south border is easily accessed from E. Watertower St. The two lots are currently zoned as CG whereby a Flex Space is an allowable use and was subsequently reviewed and approved by Sonya Waltters and Anna Borchers in the Planning Department. The property is well suited for the proposed facility. Its adjacency to the existing Schwan's Home Service Facility directly to the north would deem it a very efficient use of land. This narrative completes our formal Certificate of Zoning Compliance application submittal. Please provide a written response and/or approval at your earliest convenience. If you have any questions, do not hesitate to call. Respectfully submitted, Jeffrey L. King CC: Joe Henn, The Schwan Food Company 1185 Grove Street • Boise, Idaho 83702 •208.336.4900 • Fax: 208.343.3531 www.ctagroup.com • boise.info@ctagroup.com • Federal Income Tax ID #81 - 0305543 AFTER RECORDING MAIL T0: File No. NCS-187059-MPLS ADA COUNTY RECORDER J. DAVID NAVARRO AMOUNT 6.00 2 BOISE IDAHO 01117/06 04:43 PM { { DEPUTY Vicki Allen �f I,��I�II�II�II'If RECORDED -REQUEST OF 1060080'?7 First American QUITCLAIM DEED Date: Dere ri ber For Value Received, Schwan"s Home Service, Inc., a Minnesota corporation do(es) hereby convey, release, remise, and forever quit claim unto Schwan's Consumer Brands North America, Inc., a Minnesota corporation whose address is 115 West College Drive, Marshall, Minnesota, 56258, the following described premises in Ada County, Idaho, to-wlt; Lots 9 and 10 In Block 1 of MURDOCH SUBDIVISION NO. 2, according to the plat thereof, tiled in Book 83 of Plats at Pages 9158 and 9159, records of ADA County, Idaho together with their appurtenances. IN WITNESS WHEROF, the Grantor, pursuant to a resolution of its Board of Directors has caused its coporate name to be hereunder subscribed by its � (title) this 12-::) day of December, 2005. SCHWAN'S HOME CE, INC. BY: yr lZ-. ,`'a.H'"l-2�✓ Its S'2eY.Q,{tr t t� Page 1 of 2 s APN: Quitclaim Deed - continued File No.: NCS-187059-MPLS (bag) Date: 11/28/2005 STATE OF MINNESOTA ss. COUNTY OF LYON ) On this `day of December, 2005 before me, a Notary Public in and for said State, personally appeared $ir;aA-t R- Sarf4--IQP , the C i of Schwan's Home Service, Inc., known or Identified to me to be the person(s) whose names Is/are subscribed to the within instrument, and acknowledged to me that he/she/they executed the same on behalf of the corporation. In witness whereof, I have hereunto set my hand and affixed my official seal the day and year in this certificate first above written. Notary Public of Minnesota Residing at: Marshall, MN My Commission Expires: 1- I.dr6 KKTA:TR NA M. 0UI$BUC MWOMon EnpIW 1-31.7A08 Page 2 of 2 AFTER RECORDING MAIL TO:. RETURN TO: First American Title Insuranee Company 1900 Midwest Plaza West 801 Nicollet Mall Minneapolis, MN 55402 . 0 ADA COUNTY RECORDER J. DAVID NAVARRO AMOUNT 9.00. BOISE IDAHO 10/31/05 12:20 PM DEPUTY RonnieOberbillip III'III,IIII'fI�III,III�I��I'I�I"II RECORDED—REQUEST OF 10516944 First American CORPORATE WARRANTY DEED File No.: NCS-187059-MPLS NCS EA MIPLS(MB)Date: October 21, 2005 For Value Received, John Flaherty Construction, Inc., a corporation duly organized and. existing under the laws of the State of Idaho, Grantor, does hereby grant, bargain, sell and convey unto Schwan's Home Service, Inc., a Minnesota Corporation, Grantee, whose address is 115 West College Drive, Marshall, MN 56258, the following described real estate, to wit: Lots 9 and 10 in Block 1 of MURDOCH SUBDIVISION NO. 2, according to the plat thereof, filed in Book 83 of Plats at Pages 9158 and 9159, Records of Ada County, Idaho. SUBJECT TO current years taxes, irrigation district assessments, public utility easements, subdivision and U.S. patent reservations and the following items: Right of way for Hunter. Lateral. Easement, reservation, restrictions and dedications as shown on the plat of Murdoch Subdivision No. 2. Easement including. terms and provisions contained therein: Agreement for Pressurized Urban Irrigation System (PUIS) with Restrictive Covenants recorded March 23, 2000, as Instrument No.. 100021772 and 100021773 and Addendum recorded September 10, 2001, as Instrument No. 101092830, Ada County Records. Said Agreements and Addendums were incorporated by Addendum recorded September 20, 2001, as Instrument No. 101092830, Ada County Records. Develo ment A reement u on the terms conditions and provisions contained therein: Recording Information: 93291 Book 150 of Deeds at Pae 201 In Favor of: Nampa & Meridian Irri ation District For: right of way together with rights of ingress and egress for the irriciation ditch Agreement for Pressurized Urban Irrigation System (PUIS) with Restrictive Covenants recorded March 23, 2000, as Instrument No.. 100021772 and 100021773 and Addendum recorded September 10, 2001, as Instrument No. 101092830, Ada County Records. Said Agreements and Addendums were incorporated by Addendum recorded September 20, 2001, as Instrument No. 101092830, Ada County Records. Develo ment A reement u on the terms conditions and provisions contained therein: Page 1 of 3 Dated: May 16 2000 Parties: City of Meridian and Howell Murdoch Development Corporation, an daho cor oration Recorded:. May. 25,.2000 Instrument No.: 1100040596 Page 1 of 3 The effect of a map purporting to show the land and other property, filed in Record of Survey No. 4998, recorded May 26, 2000, as Instrument No. 100040977 of Record of Surveys. License A reement upon the terns conditions and provisions contained therein: Dated: February15 2001 Parties: Nampa & Meridian Irrigation District Recorded: February 23, 2001 nstrument No.: 101015634 Addendum to License Agreement recorded August 24, 2001, as Instrument No. 101086660 Easement including terms and provisions contained therein: ecording Information: 101015635 n Favor of: Nampa & Meridian Irrigation District For: replacement right of way for Hunter Lateral License Agreement upon the terms, conditions and provisions contained therein: Dated: ctober Z 2001 Parties: Nampa & Meridian Irrigation District and Idaho Power Company Recorded: ctober, 9, 2001 nstrument No.: 101103718 Covenants, Conditions, Restrictions and Easements recorded February, 8, 2002, as Instrument No. 102016510, Ada County Records, but deleting any covenant, condition or restriction indicating a preference, limitation or discrimination, based on race, color, religion, sex, handicap, familial status, or national origin to the extent such covenants, conditions or restrictions violate 42 USC 3604(c). TO HAVE AND. TO HOLD the said premises, with their appurtenances, unto said Grantee, and to the Grantee's heirs and assigns forever. And the said Grantor does hereby covenant to and with the said Grantee, that the Grantor is the owner in fee simple of said premises; that said premises are free from all encumbrances,. and that Grantor will warrant and defend the same from all claims whatsoever. IN WITNESS WHEREOF, the Grantor, pursuant to a resolution orits Board of. Directors has caused its corporate name to be hereynto subscribed by, its fed Q,,,-�- this ZS4 day of ©c_lCo hs -r Page 2 of 3 r• � APNA-5901-17-0010 Warranty Deed He No.: NCS-187059-MPLS (bag) 8-5901-17-0020 - continued Date: 10/21/2005 John Flaherty Construction, Inc. By: vl,v M6; L STATE OF IDAHO ss. COUNTY OF fielC, ) On this d y O=!eZIZ before me, a Notary Public in and for said State, personally appeared known or identified to me to be the f/1P �&X0_1L of the corporation that executed the within instrument or the person who executed the instrument on behalf of said corporation, and acknowledged to me that such corporation executed the same. In witness whereof, I have hereunto set my hand and affixed my official seal the day and year in this certificate first above written. ��prrrrrrrrr` 4 ,;r'N '•...� �. Notary Public or the State of Id o tea« �oTAk jt. Residing at: • : My Commission Expires: rL`rOF 1,M�0 Page 3 of 3 } r ADA COUNTY RECORDER J. DAVID NAVARRO AMOUNT 6.00 2 BOISE IDAHO DEPUTY Vicki Allen 06 04:43 PM RECORDED—REQUEST OF III 106009097 lII First American AFTER RECORDING MAIL TO: QUITCLAIM DEED File No. NCS-187059-MPLS Date: December 31 2r0z For Value Received, Schwan"s Home Service, Inc., a Minnesota corporation do(es) hereby convey, release, remise, and forever quit claim unto Schwan's Consumer Brands North America, Inc., a Minnesota corporation whose address is 115 West College Drive, Marshall, Minnesota, 56258, the following described premises in Ada County, Idaho, to -wit: Lots 9 and 10 In Block 1 of MURDOCH SUBDIVISION NO. 2, according to the plat thereof, filed In Book 83 of Plats at Pages 9158 and 9159, records of ADA County, Idaho together with their appurtenances, IN WITNESS WHEROF, the Grantor, pursuant to a r solution of its Board of Directors has caused its coporate name to be hereunder subscribed by its (title) this � day of December, 2005. SCHWAN'S HOME CE, INC. Its Y'Lt0'.'_ Page X of 2 APN: Quitclaim Deed - continued File No.: NCS-187059-MPLS (bag) Date: 11/28/2005 STATE OF MINNESOTA SS. COUNTY OF LYON ) On this `day of December, 2005 before me, a Notary Public in and for said State, personally appeared 13r.*avk R•Sczikla-�, theme of Schwan's Home Service, Inc., known or Identified to me to be the person(s) whose names Is/are subscribed to the within instrument, and acknowledged to me that he/she/they executed the same on behalf of the corporation. In witness whereof, I have hereunto set my hand and affixed my official seal the day and year in this certificate first above written. Notary Public of Minnesota Residing at: Marshall, MN My Commission Expires: 1- 3I-01? KATFtINA M. DUiI$ NOTARY PUBUC ^ t4aFa�E M 6"y Cana ission Expires 1-31-2001 Page 2 of 2 .y f ADA COUNTY RECORDER J. DAVID NAVARRO AMOUNT 9.00 BOISE IDAHO 100/05 12:20 PM AFTER RECORDING MAIL TO:. DEPUTY Bonnie Oberbillig RECORDED -REQUEST OF III 105IIIIIIII163944 1IIIIIIIIIIIIII IIIII First American 185 RETURN T0: First American Title Insurance Company --"� 1900 Midwest Plaza West 801 Nicollet Mall Minneapolis, MN 55402 . CORPORATE WARRANTY DEED File No.: NCS-187059-MPLS NCS MPLS(MB)Date: October 21, 2005 For Value Received, John Flaherty Construction, Inc., a corporation duly organized and. existing under the laws of the State of Idaho, Grantor, does hereby grant, bargain, sell and convey unto Schwan's Home Service, Inc., a Minnesota Corporation, Grantee, whose address is 115 West College Drive, Marshall, MN 56258, the following described real estate, to wit: Lots 9 and 10 in Block 1 of MURDOCH SUBDIVISION NO. 2, according to the plat thereof, filed in Book 83 of Plats at Pages 9158 and 9159, Records of Ada County, Idaho. SUBJECT TO current years taxes, irrigation district assessments, public utility easements, subdivision and U.S. patent reservations and the following items: Right of way for Hunter. Lateral. Easement, reservation, restrictions and. dedications as shown on the plat of Murdoch Subdivision No. 2. Easement including. terms and provisions contained therein: Agreement for Pressurized Urban Irrigation System (PULS) with Restrictive Covenants recorded March 23, 2000, as Instrument No.. 100021772 and 100021773 and Addendum recorded September 10, 2001, as Instrument No. 101092830, Ada County Records. Said Agreements and Addendums were incorporated by Addendum recorded September 20, 2001, as Instrument No. 101092830, Ada County Records. Develo ment Agreement upon the terms conditions and provisions contained therein: Recording Information: 93291 Book 150 of Deeds at Page 201 In Favor of: Nampa & Meridian Irrigation District For: right of way together with rights of ingress and egress for the irrigation ditch Agreement for Pressurized Urban Irrigation System (PULS) with Restrictive Covenants recorded March 23, 2000, as Instrument No.. 100021772 and 100021773 and Addendum recorded September 10, 2001, as Instrument No. 101092830, Ada County Records. Said Agreements and Addendums were incorporated by Addendum recorded September 20, 2001, as Instrument No. 101092830, Ada County Records. Develo ment Agreement upon the terms conditions and provisions contained therein: Page 1 of 3 Dated: May 16 2000 Parties: City of Meridian and Howell Murdoch Development Corporation, an daho corporation Recorded:. May. 25, 2000 nstrument No.: 1100040596 Page 1 of 3 The effect of a map purporting to show the land and other property, filed in Record of Survey No. 4998, recorded May 26, 2000, as Instrument No. 100040977 of Record of Surveys. HcPnsP- AarPPmP-nt iinnn the tarrnc rnnriitinne nnri nrmAcinne r-nn+n;naA +-1--in. Dated: Februaa 15 2001 Parties: Nampa & Meridian Irrigation District Recorded: February 23, 2001 Instrument No.: 101015634 huuenuum tv 4fcense Agreement recoraea August z4, zuu1, as Instrument No. 101086660 .asement including terms and provisions contained therein: ecordin Information: 101015635 n Favor of: Nam a & Meridian Irri ation District For: Ireplacementoght of way for Hunter Lateral LicPnsP AarPPmPnt iinnn the tPrmc- rnnriitinne znrl nrnvicinne rnnf•!%inmA f-hnrc,ir.. Dated: ober 2 2001 Parties: [Nampa& Meridian. Irrigation District and Idaho Power Company Recorded: ober, 9, 2001 nstrument No.: 103718 Covenants, Conditions, Restrictions and Easements recorded February 8, 2002, as Instrument No. 102016510, Ada County Records, but deleting any covenant, condition or restriction indicating a preference, limitation or discrimination, based on race, color, religion, sex, handicap, familial status, or national origin to the extent such covenants, conditions or restrictions violate 42 USC 3604(c). TO HAVE AND. TO HOLD the said premises, with their appurtenances, unto said Grantee, and to the Grantee's heirs and assigns forever. And the said Grantor does hereby covenant to and with the said Grantee, that the Grantor is the owner in fee simple of said premises; that said premises are free from all encumbrances,. and that Grantor will warrant and defend the same from all claims whatsoever. IN WITNESS WHEREOF, the Grantor, pursuant to a resolution o its Board of. Directors has caused its corpor,name to be here nto subscribed by, its �re��'r,- this 2..5� day of Q�kCohef , 20_1�. Page 2 of 3 • r • h iO J ti i:- APN:R-5901-17-0010 Warranty Deed R-5901.17-0020 -continued John Flaherty Construction, Inc. STATE OF IDAHO ) ss. COUNTY OF RAL, File No.: MCS-187059-MPLS (bag) Date: 10/21/2005 On this d y October, 00 , before me, a Notary Public in and for said State, personally appea}ed g known or identified to me to be the /19 jfro its of the corporation that executed the within instrument or the person who executed the instrument on behalf of said corporation, and acknowledged to me that such corporation executed the same. In witness whereof, I have hereunto set my hand and affixed my official seal the day and year in this certificate first above written. ,���rUMrrurrrr. �•`� �..���.�« Notary Public for the State of Id o cli! OTAR c Residing at: go My Commission Expires: P. Z.� `�'UBL.Z•C' �. Page 3 of 3 AFFIDAVIT OF LEGAL INTEREST STATE OF MINNESOTA COUNTY OF LYON I, Schwan's Consumer Brands North America, Inc.. 115 gest. College Drive (Name) (Address) Marshall Minnesota 56258 (City) (State) beim first duly sworn upon, oath, depose, and say: l . That I am the record owner of the property described on the attached, and I grant my permission to: CTA Architects Engineers, (Name) 1185 Grove Street Boise Idaho 83'702 (Address) (City) (State) to submit the accompanying application pertaining to that property. 2. I agree to indemnify, defend and hold the City of Meridian and it's employees harmless from any claim or liability resulting from any dispute as to the statements contained herein or as to the ownership of the property, which is the subject of the application. Dated this �9- day of 6ryr l~ aEg , 2006. SCH'4'arAN'S CONSUMER I3RANDS NORTH AMERICA, INC. (Sig e) BY: Brian R. Sattler ITS: Secretary SUBCRIBL-D AND SWORN to before the the day and year first above written. AUVA10KCHNI©M Notary Public for LY0A1 %V0wA*a1 Residing at r i11 u, N 6&f1 My Commission Expires; f G:ICVCMldocuments 12-19-'06 16:29 FROM -SSC ZfU88HbWbZ T-100 ?001/00b 11--16b To: IMAS Company: Sanitary Services Company, Inc. 2130 W. Franklin Road Meridian, ID 83642 Phone: 208-888-3999 Fax: 208-888-5052 From: _ i (o &o Pages Sent: (including cover sheet) Fax Number: Date: j.;- Additional Message: HOL ('(IMMFNTS-. .-%Q 1.... 66A.WA.AB 4,eev o:.O.,Jio�s,a� d.0 r.At .Arz Asrx e 61mmz. -&VAVi- C9Q fM,d /using. LG�a�A�eE e ��. �r7ra ialZt.r - -P�PY/D� a irli�l. a�iYlr �•� e4U,9AAJCA- - /AsrA4 - doGGAZ S ev -IMA /,0Si01. AMC 01' ?N -L 4j&-OSd.IL �BO✓��� d'd re s Lo ciie s e ,dont rKr� "64) � , fCcoreo Aosirlmd - 4evV IV e. !o to 40,96 , 4104-W i -J At o AJ -r o-0 9A�c & osv a G... — -,Peo✓ia4 /,(a., m o d e e e amyd 4e 6- oA.v na,4A c 9'a ACGFss t. 6e�ofao1jEQ.i Kfwe,JE✓cU-?VSsi6c1— TNA- &Ccoj&Ad . A IOCArea Oc! ir/JA4J 7'N*_ A9��cJ. S " -1,BoM A 41eoa&O -51rRd6Td dA od eA ✓-1- . 12-19-'06 16;29 FROM -SSC T-100 P0021005 F-735 ........ . ............. .. .......... , i,..� ��—A- e� — _—. — � — — —.mom.• — r — �- I 1 1 I I I • v i I 18 TMp• � VALLry is IG TVP. ri 1 I <• nca• .!� ar I J e ar . E E. WATERTOWER STREET NREF H 12-19-'06 16:29 FROM -SSC 2088885052 T-100 ?WM/W105 ]�-Yb W', -t, . k ... . . ........... ........ . ... WN 5 Schwan's Co nsumer Brands & Distribution Facility Warehouse E Watertower St Meridian, Idaho Sad 2 INI 5C 4 01 N. ..... ...... . .. . ............ . .... Schwan's Co nsumer Brands & Distribution Facility Warehouse E Watertower St Meridian, Idaho Sad 2 INI 5C 4 01 DESIGN �x DEVELOPMENT 1 CQ ) —.T crnrrn /CPM T MMT- r 7gogRRRRA7. oss-W0u3 63:9Z 90r -6Z-31 PLAT SHOWING NE saran camw MURDOCH SUBDIVISION NO. 2 CP&f to S -ti No. 9377495 A PORTION OF THE NT/2 SE 1/4 HE 1/4, SECTION 18 1 END TONSHP 3 NORTH, RANGE 1 EAST, & Found Brass Cqp BASE MERRIOUN ; o Found 5/8" Iron Pin with Cap 'PE/LS MERIDIAN, ADA COUNTY, IDAHO 3260' unless Noted Otherwise .Ir Set 5/8'x 30" Iron Pin with Plastic Cop 2002 n "t a 'PE/LS 3260" ala rn Set 1/2'x 24' Iron Pin with Plastic Cap 'PEAS 3260' UNPLATTED TRUE POINT OF ` I - - Boundary Una Mw C., o, MEDiMONT SUBDIVISION' NO. 2 BEGINNING I f MEDIMONT SUBDIVISION NO. 1 I Lot Line H 1/2 SE 1/4 NE 1/4 season ie - — Centerline of Street 1326.5 UNPLATTED- - - - - - - - - - Utility, Drainage and Irrigation Easement Una 17 02'--- --176:0 - - ---177.05'-- 168.00' w' Hun Ter Lateral I_.In an �/ �' - I m. Easement far the Banefft of '� ,: _ 166.00 166.00 166.40' m NE Com« N 1/2 SE 1/4 NE 1/4 (See Note 3). 0 Nn Found 5/8', No Cap Set Cap, PEAS 328Nampa "1N & Meridien Irrlgatlon / BLOCK 1 ,«15'--5 BLOCK 3 o N N CP&F Na 8Ba3845 District5 48.00 =c.�'1O2 Tz� o oonn 0 ori 3 i 4 m I E�ai 544'44'04"E 'n 'd row 55.98' ,n b rov 54439'36"IN o N45"2024WN I o y N o m or 1. Buildin setbacks and dimenslond standards In this aubdlNsion shall be in compliance with the applicable zoning regulations of the 9� 28.28• -L 28 28' N45'OS'39'E rn f n City of Meridian. Idaho. ---179.02 o - '- - --157.05'-- o --148.00'-- ---166.00'-�----166.00'--- 35.62 N , --163.30'-- O 2 Any Re -subdivision this _ C) --' -- 176.0 - o, m N 1+1 r0 Z of plat shall comply with the applicable Zoning Regulations in effect at the tineof the Re -subdivision. Z N 561.54' 764.87'Z N89'39'40"E 1326.41' C iD 0 E. WATERTOWESTREET 3. All lot Iln" common to the exterior boundary and to public >right-of-way lines within Murdoch Subdivision No. 2 as shown hereon -r-------- 7 ----- - --1010.31'---------------------- ---24���--- -O shall have a 10' wide Permanent Utilities, Drainage and Irrigation w' Haatw Lateral brigeaon S4444'04"E - _ m - 114'4�E Easement, unless otherwise dimensioned. However, this shall not ,o Eaewn.ne r« the e.nem or 67.81' - .n > V)preclude the construction of proper hard surfaced driveways for to r0 Nampa & Meridlan brigallon Dletrlt HUNTER LATERAL -O I4�+ ccess to each individual lot. ,P \ O 4. The Developer and/or Owner shall comply with Idaho Code, Section Jy o at 589'28'45'E le m 31-3805 or Its provisions that may apply to Irrigation rights. C3 NI ne �$ 243.05' ~ 5. The owner of each lot, across which passes an Irrigation/drolnage O m 9c `?Sa 1 1 3 < F N o ditch or pipe, is responsible for the maintenance thereof unless such o No a \ 1 a 10 �I tp� z responatblllty has been assumed by an Irrigation/Drainage District. --- _- Z `ad'• 1 11 �• 1 6 vi 3 =1 b- v $ N 16 6. Reference is hereby made to Record of Survey No. 4546 filed as BLOCK 2 n S89'28'45'E M Instrument No. 99018564 for further survey Information. P 1 61,r 243.05' 7. The bottom elevation of building footings shall be a minimum of p 11 1�1 0 30' vnae Ingress ane -.I o Z I 12 inches above the highest established normal groundwater lel I 1 N E9ren Easemml fw of Lots I „fit $,00'I Q alevatlon. EL 1 1 10 d 11. 10 and 11, Block 2 - m 11 m 8. Drlvewo roach size and location shall be y Y say approved b The Ado Z 1 �1 o m - County Highway District D - 427.6' 1 1` 1010.13 _ ^ 243.09' x a 113, 9. Direct lot access to S. Locust Grove Rood Is prohibited, except as - PIs 78-5 $8936'07" W _ _ _ _ _ _ _ 1326.23' PLS 7314 In shown hereon, unless specifically approved by the Ada County Highway District and the City of Meridian. SW Comer N 1/2 SE 1/4 NE 1/4 - m m - 10. Lot 12 of Block 2 and Lot 5 of Block 3 are common lots to be - I e I owned and maintain by the Murdoch Subdivision No. 2 Owners UNPLATTED I Association. SE C-er N 1 / /22 SE t/4 NE 1/4 E Y 11. The Cit of Meridian is the Owner of Lot 8, Block 2. .t� OWNE DEVELOPER: HOWELL-MURDOCH DEVELOPMENT CORPORATION KEVIN HOWELL, President m w 1087 West River Street, Sults 250 o a I n Boise, ID 83702 (208)383-4302 AND z CITY OF MERIDIAN C- 1Z 33 East Idaho Street SW 1/4, NE - E 1/4 C— Idaho -1/4 Sauon 18 _ Secuon 18 CP&F No. (208) 868-4433 - 8251242 Oyjl 260 J -U -B ENGINEERS, INC. SCALE: 1"=100 0' sn /J-Dz. '" > �j- Enghivo-s SLywK s P/a7ndf9 - of \0�4 - Boise, Idaho �Rr A. 116/43FP1.aWC PLAT BOOK PAGE SHE oz 1 OF 2 CERTIFICATE OF OWNERS MURDOCH SUBDIVISION NO. 2 CERTIFICATE KNOW ALL MEN BY THESE PRESENTS: That HOWELL-MURDOCH DEVELOPMENT CORPORATION, an Idaho Corporation and the City of Meridian, Ada County, Idaho does hereby certify that they are the owners of a certain tract of land as shown on this plat and described as follow., and Intend to include sold land In this plat. A parcel of land being the North yt of the Southeast 9 of the Northeast 34 of Section 18, 13N., RAF_ B.M., Meridian, Ada County, Idaho; being more particularly described as follows; Commencing at a brass cap marking the Northeast comer of acid Section 16; thence along the Easterly boundary of said Section 18, South 00'31'15` West, 1,329.55 feet (formerly known as 1,326.55 feet In that certain Warranty Deed recorded as Instrument No. 98094973 In the records of sold County) to a point marking the Northeast comer of said North % of the Southeast Xr of the Northeast 34, sold point being the REAL POINT OF BEGINNNING; thence continuing along said Easterly boundary South 00'31'15' West, 664.63 feet to a point marking the Southeast comer of sold North )¢ of the Southeast X of the Northeast %; thence leaving said Eoaterly boundary along the Southerly line of saki North % of the Southeast )E of the Northeast 34 South 8936'07' Wast, 1,326.23 feet (formerly known as South 8936'01' West, 1,326.19 feet) to a point marking the Southwest comer of said North % of the Southeast M of the Northeast X: thence leaving sold Southerly boundary along the Westerly line of said North X of the Southeast 34 of the Northeast X North 0029'39' East, 666.00 feet (formerly known as North 00'29'35' East, 665.99) feet to a point marking the Northwest comer of sold North % of the Southeast % of the Northeast X; thence leaving void Westerly boundary along the Northerly line of mid North 14 of the Southeast X of the Northeast K Nath 8939'40` East, 1,326.53 feet (formerly known as North 89'39'34' East, 1,326.49 feet) to the REAL POINT OF BEGINNING. Sold parcel contains 20.26 acres, more or las& The public streets as shown on this plot. are hereby dedicated to the use of the public, and the eaaamertts indicated on odd plat are not dedicated to the public, but the right to use sold easements Is hereby reserved for public utilities and any other uses as designated hereon and no permanent structures are to be erected within the lines of said easement. AI lots shown on this plat are eligible to receive domestic water service from the City of Meridian. Idaho, Municipal Water System. Further, the City of Meridian. Idaho has agreed In writing• to serve all lots within this subdivision with domestic water IN WITNESS WHEREOF, we have hereunto set our hands this U0, of MA� _ 2001. HOWELL - MURD/OCH DEVELOPMENT CORPORATION CITY 9FMERIDIAN °F"°4t, 4 BY•��[-,—�1 7—dna.—Y P .vin Alt Howell. President Roblert 0. Corrie, MayvrAL T ANN CERTIFICATE OF ACKNOWLEDGEMENT STATE OF IDAHO) BY e's��,,•'r tat •, ,�r� COUNTY OF ADA)'. William G. Berg, Jr., Cffy4taorkr On this 1412 day of - A/ v 200y before me 1a�.y /� W.'�.( a notary public In and for sold state• personally appeared .vin A. Howell• known or Identified to me to be the presidan of the corporation that executed the above instrument or the person who executed the above Instrument on behalf of mid corporation, and acknowledged to me that such corporation executed the some. IN WITNESS WHEREOF, I hove hereunto set my hand and affixed my official seal the day and year first above written. ',tw"w,wa..lY STr' NotElry'Publi. far oho�— s� ,l0TAq` * ASI LIG • Residing at �+<< Idw, *� My Commission Expires Z/W2.4 CERTIFICATE OF ACKNOWLEDGEMENT STATE OF IDAHO) - COUNTY OF ADA))sa On this 2h day ofTK(v1 200L before me GA m D. 1m-,-�k a notary public in and for said state, personally appeared Robert D. Corrie, known or Identified to me to be the Mayor and Willam G. Berg, Jr. known or Idmtlfiedto me to be the Cily Clerkof the Cityof Merldim, Ada County, Idaho that executed the above Instrument and acknowledged to me that such City of Meridian, Ada County, Idaho excuted the same. IN WITNESS WHEREOF, I have hareunto set my hand and affixed my official seal the day and year feat above written. AreffOd' S�/lyre Notary Public f6r Idaho NOTAg7, Residing at hldj,diA^• rA(A- * Ai180C' * My Commission Expire. 1iI7 O ` CERTIFICATE OF COUNTY TREASURER I, the undersigned, County Treasurer In and for the County of Ada. State of Idaho, per the requirements of I.C. 50-1308, do hereby certify that any and all current and/or delinquent property taxes for the property Included In this proposed subdivision have been paid In full. This certification Is valid for the next thirty (30) days only.yvfr yreQaures Dat.—j--f 1a2 a_ OF SURVEYOR 1, Gary A. Lee, do hereby certify that I am a Professional Englnew and Land Surveyor, licensed by the State of Idaho, and that this plat, as described In the Certificate of Own ero and on the attached plat, was drawn from an actual survey, made on the ground under my direct supervision and accurately represents the points platted thereon, and Is In conformity with the State of Idaho Code relating to plots and surveys and the Comer Perpetuation and Filing Act, Idaho Code 55-1601 through 55-1612. I Gary A. Lee, P.E./LS. ' 26 License No. 3260 S- SSA APPROVAL OF CITY COUNCIL e qMY A. I, the undersigned, Gty Clerk and for Cig of MERIDIAN, Ada County, Idaho, do hereby certify that at a regular meeting of the City Council held on the I_ day of f+\sT2001, this plat was duly accepted and r o City perk, City of Merididin, Iffaho ay..L _ 9p Lit' ADA COUNTY HIGHWAY DISTRICT COMMISSIONER'S ACCEPTANCE Th f olnpl2001 s accepted and opTrO` Nd'fl�` d of Ada County Highway District Commissioners on the 177- day of tf ADA CO/UJN�TY HIGHW Y DISTRICT s I J /W/i.[,Fi sy f ,! Chairman 00.,tlOd - CERTIFICATE OF COUNTY SURVEYOR 1, the undersigned. Profes imal Land Surveyor for Ada County, Idaho, hereby certify that I have checked this plat and find that It compiles with the State of Idaho Code relating to plats and survey.. -c''. . *a• 134L 2 e APPROVAL OF CITY ENGINEER I, the undersigned, City Engineer in and for City of MERIDIAN, Ada County, Idaho, hereby approve this plot BY• /Jiw.r/,PGJrao yo Date /a/ APPROVAL OF CENTRAL DISTRICT HEALTH DEPARTMENT Sanitary restrictions of this plat are hereby removed according to the letter to be read on file with the County Recorder or his agent listing the conditions of approval. COUNTY RECORDER'S CERTIFICATE IRSTRUMENT NO. IQ;L� Ant 047 - STATE OF IDAHO) SS County of Ada )) BY N .4NEALfN en 1 atr a Heal aper an 4 A Date t.V 0 w wDA c C-0 a * y I hereby certify that � I. Instrumen a filed at the request of 3 U S E'n `API -S D_ o'clock P- m., this I �4` da of -\c A w�. m °t --� —minutes post Plats at pages 'i S K and y I 2�L in my office and was duly recorded In Book _ of FEE $11.00 eputy Ex-Offlcio Recorder M. — SHEET 2 OF 2 1260 E. Watertower Lane Vicinity Map U H m J FRANKLIN - -- - --- ------ -- PIPER- ---- U Q -T SCENERY i --.-.. — —KALISPEL-L SCkIILLER \ �\ - -� F- - - WATERTOWER _._ -- ..._._.-.._...-.1—.— D —cn U U) BOLLMAN, — — ILI Co PRATT (l , C _.-� C/) -0 cn - -\ I L_i__L I � I Schwan's Warehouse Site M 1250 3U� E KALISPELL ST Legend .,.t� h z, 300 Major Streets �. N MINOR ARTERIAL - a 00 MAJOR COLLECTOR SECTION of PRINCIPAL ARTERIAL 123 ` - 1267 Z of INTERSTATE .44 Minor Streets a N LOCAL :i 360 i✓ PARKS pv PRIVATE RESIDENTIAL - N 00 Other Street Names (minor) Addresses C3 Parcels Ada-OQ2003 C3 Schools 1090 1 5 12UQ 126 1 a Parks City Limits n� Kuna C3 Boise Q Garden City C3 Eagle El E WATERTOWER ST p Meridian ® Other 1.U85 114• 1401 N Scale: 1:2,572 This map is a user generated static output from an Internet mapping site and is for general t reference only. Data layers that appear on this map may or may not be accurate, current, or otherwise reliable. THIS MAP IS NOT TO BE USED FOR NAVIGATION. FORM PW100 CITY OF IDAHO c� q ° TREASURE V n�� 1903 MAYOR Tammy de Weerd CITY COUNCIL MEMBERS Keith Bird Charles M. Rountree Shaun Wardle Christine Donnell CITY DEPARTMENTS Fire 540 E. Franklin Road 888-1234 / fax 895-0390 Parks & Recreation 11 W. Bower Street 888-3579/fax 888-6854 Planning. 660 E. Watertower Street Suite 202 884-5533 / fax 888-6854 Police 1401 E. Watertower Street 888-6678/fax 846-7366 Public Works 660 E. Watertower Street Suite 200 898-5500 / fax 895-9551 - Building 660 E. Watertower Street Suite 150 887-2211 / fax 887-1297 - Sewer (WWTP) 3401 N. Ten Mile Road 888-2191/fax 884-0744 - Water 2235 N. W. 8th Street 888-5242/fax 884-1159 Date: 12/20/06 The following address has been verified by City of Meridian Public Works Department as valid for the project listed below. Project Name: Schwans Consumer Brands Address: 1260 E Watertower Suite #: Zip Code: 83642 Lot /Block/ Subdivision: L 10 / B 1 Murdoch #2 Notes: EACH SET OF PLANS WILL BE REQUIRED TO CLEARLY REFLECT THE CORRECT ADDRESS AND SUITE NUMBER (IF APPLICABLE). Tricia Shindle City Of Meridian Public Works Department 660 E Watertower Street Suite #200 Meridian, ID 83642 PH. 208-898-5500 FX.208-898-9551 bierent@meridiancity.org CITY HALL 33 EAST IDAHO AVENUE MERIDIAN, ID 83642 (208) 888-4433 CITY CLERK - FAX 888- 4218 CITY ATTORNEY/ HR - FAX 884- 8723 FINANCE & UTILITY BILLING - FAX 887- 4813 MAYOR'S OFFICE - FAX 884-8119 iaoc. �� I Asa eTE�wAuf9� L AiaffDA F9 �� xoTe:vPonoeco:+raaa reLwmAN �,� DI�„9DDY o�,m°I°RBnD� vAD : CURB & WALK ab+ acue ,a.l iT�ine�we- - uxrm emfEa - wTmow,s wN„E BeeDED REAECDVe PNM. - Q eET,m,MPuuENo sAu SYMBOL OF ACCESSIBILITY - 4 090+ SYMBOLLEGEND A6mTTPPYDT+OBITA �. A@�-■ e,T+ro9fAov9TmEm AAPNLLTPAVOb � PAWA`NTY v°AxnO�� �uTro aTmT,Ta auvuaam neanne. �� TaoPwW9T+INVA � caxrnTE •aow9ereaeormYTE NOTM AammeIEPAMmIO TmI erAfO�TE.TOxD,ncLL KEY NOTES coomAwamu norw e ACCESSIBLE SIGN comTSP°°o,°EE"m edue +D+.r z DarhwArlvveaaavenm,AYY AAl9va TsaTL n AerAATaWYLeaum.eeeeemL COYCAEIE CYRn l I 40. PRBIXIAIV).Bm OEfALLiS1101. vou:eEAeEaee,RH,. - 0. PUYRNAafl�am L1.1. 1. AOCTIBIeIA IWP,TS 6gb1. 6 ACCm010,LMIF.9EEd0A• 1. � / a a eETeAucpYmoxrnrAArtasoeuxoee.Peeuvxip MAT¢o Yb wATAum er awrmL EmTVAIN Aus a De�eNLcoMwcionmmorbware Merw.LnoN. A•V. NAw�ve n. eTNM;NwNDxeIEPADvonmuwueM. ' +z fnWxwxcvzreTwxavTax»aeule®vomm.erarw•r. 4 ACCEBTTPPAWTIDAPACO. PAMTPWILE BTpPm ATAP6G Wnx TNOCBAIOACCmBYIl MUE k eY160lOPACCmTYY,Y. VI ICN,. CURB RAMP SECTION n IYAoort,9¢xrAccme pfa Yuy �' +YM u oonmureoaxnbLJoxrTrneu.. +T. BACNNV�VWIDI✓EIETNT, @1pO011ee PIDYOMBIJ10O 1l OATYP. +Y• De® JOIHIAATf B.C. ,6 GOMOIEIEPADPoRTJLINCALIrt6rtYTTNIBWxtlTtOEE VHDL -TOV OF PAVMD IL VAYAYIXRTHLOEE CTA - vAvwoexArp m awTevAaaxoATM9.aTafPMa PwrtTwocaTATaAPPA:r¢Low. roeevu,al - H. aTM T®PoVENi0R4iT.9EEChl_ 9z evsmbwAanoNAozroATNM ,aewxsuwe m cwnwuousaNwereaTaaEEDlw_ oonevErEs,IAYTN 9s AT.,o+>?me,ubadT IMKPENCeeNLAElATE00EY0. �IHFOPCEYEM m PENDVEPBanOX OP FABTMO BeAIaWCCM060Vn9IPoeNEW - MGdlT. CONB1xUCDOte . m WBYfl0q,0Tt1HN2 - CURB RAMP T. aemew,u/Lemu®T. _ e� xl' - m PTNICIt WlKpeTeeTEwAIK 9L CONGVEIEP.WP,0m CM. - xi umrt vaznelAe eeA,/EH,. GENERAL NOTES eDNe axonwrix W'TOOIIDJONR A. LOGTY]NBPMCaroEIRJ�VAFAeTIxG CONDRMixnAM EIOBTPb IIRnY ATP O.C,Try COYG aAYP E' HRmTe�ffBNm� YP�JTO,B NBMIO FlO0T010BDWCD1Am Alb PfpAT E.Drc ro M000NL CBNOBIOY A uuT¢ NIA BLS,IRAe0 oLTebooxmAuonola - C. CONIPIDIORTNLL PADJTEALLDT90LRIOX MCTpTALroOe ' nenT vP�xeveoxarnunmxwxemeNoaxorrtlDevecuwur _ rw,m.emavaHNwmoa voae,rmoT,,amax rT.vl aeE � d� D TEARLYLW02D VTBCULAa COVXAATOHNDtW ALLeIEEE,B.Am PADW a IPAFnC CDNIaDL MPABUFTB N a Mb�vEYBPEO9lGTIW PAVBYEHTMNBTbOTd KNOWN ONPIAYB P. e9vymElWLeElbx uxoenvAwmTlAr�wMm erw+wuve RAMP COMxACIDK TNLLBEl CIME9IA PVCANDEKBTA AVEMBNR ON TURN TOE em LANDBGPE y. a NIA d COTbV,AT0ALL0Re Wdix BNONN W/CNADPAINNGe. k PR.OVIOe OxADE Ib[U,bE4ALLCCNCWEiEPADB, WAWANDnU89. - T2CIVLOxAMx0a ARCHITECTURAL O SITE PLAN Ems,,. ,•-mo N�11 SITE CALCULATIONS m w�N�owoTvaoTc A,oeart. K PIAMIYB BTAl9A WL11TPD: TA,TWO-+0 aFPAAgY00TALLEmWIDE¢ 10 6E10AOQC ma PAONT - 6d BDELANOBDVEBUFFFA 61 PLANT SCHEDULE �1 DECIDUOUS TREE DETAIL ua -Tri xswuunxoxrwn e"x"E,x.wwunnv�,omr LEGEND NOTES- - ••••�,ea.�®w.aemeri.�"eoenum.roxn.®,vsaa �1 CONIFEROUS TREE PLANTING a caxm.em"auuaoumw.renxmo.nx, wevanx.r.,e�urwrrewrKu,,a neussmvrcruvm�mewx..emew,riaxwr�waaworta+Kiwm�`�`.au` roi�mn S� v x ,name«�.w�maw�m�r,"�nuw*'�.wweroe� vv�wnec�,aoF.a�,o,a.�ea,cmow anmm�r. �. o.a x.w+wwecp�mw,ianmoieuvroxnwwvaa�eveuu�rwiaNwrrrmunwnn�a, v.� u1.uiownouxoe,a"nuw �u�urcxmmyrw.romu��imnieiar+mwoowaa u�"`ri.�o.�wu,nm �am�e�"za�eu�`a,w�orr�s`�uwe��nmreueamua�x-r. SHRUB PLANTING DETAIL u., C1 EDGING, MULCH & FABRIC u,, xro LANDSCAPE PLAN .ma e"�"wer`,xTOe semi mCOew","wu wm on"'"�ixNw"e a� n S 5 G L Landscape Calculations Schwan's Consumer Brands Warehouse & Distribution Facility E Water Tower Street, Meridian, Idaho Lineal feet of street frontage - 176' Number of street trees - 6 Width of street buffers (exclusive of right-of-way) - 25' Width of parking lot perimeter landscape strip - 5' minimum Number of parking stalls -16 Percent of parking area with internal landscaping - 9% Total number of trees - 17 Tree species mix - 5 P.O. Box 170204, Boise, Idaho 83717-0204 Phone/Fax: 208)336-3005 E -Mail: toby@goodearthlandscape.biz HBB';• www.goodearthlandscape.biz -T® Member sw Idaho ARCH ITEC`TS ENGINFERS January 5, 2007 City of Meridian Planning & Zoning Department 660 E. Watertower Lane, Suite 202 Meridian, Idaho 83642 RE: Schwan's Consumer Brands Warehouse and Distribution Facility E. Watertower St. Meridian, Idaho 83642 Dear Sir or Madam: Per Meridian City Code 11-3A-11: Outdoor Lighting, the new Schwan's Consumer Brands Warehouse and Distribution Facility located on E. Watertower St. complies with all standards set forth in the city code. Sincerely, CTA RCHITECTS NGINEERS 4 James Mesplay CTA File — 1185 Grove Street - Boise, Idaho 83702 • 208.336.4900 - Fax: 208.343.3531 www.ctagroup.com - boiseinfo@ctagroup.com • Federal Income Tax ID #81- 0305543 V61 IaM LIGHTING Type: Job: Catalog number: Fixture Fleclrical Module Finish Options See pages 3-4 Sec page 2 Specifications Maximum Fixture Weight (150HPS) = 26 Ib 13" (a3o2LL mm) 7 3/8" (187 3 mm) —T /T— 8 %8" 6 16 r 1275 4 mm) 057 2 mm) L_ 14 s/e" (371 5 mm) 43/4" DIA. Bolt Circle *�15 51/4(133.4. Bolt Circle Mounting Plate Attaches directly to any standard 4" J -box (by others) 41/2" (114.3 mm1 To J -box center HUBBELL Hubbell Lighting, Inc. 1� WD14 14" Wall Director` revision 8/01/06 • wd14.pdf Approvals: Date: Page: 1 of 5 Reflector Housing: One-piece die-cast, low copper alloy (<0.6% Cu) aluminum with integral cooling fins- Rotates against ballast houting to provide 10° of adjustment with degree markers cast into the housing. At 0° adjustment, lens is totally concealed from view above horizontal with fixture aimed downward. Ballast Housing: One-piece die-cast, low copper alloy (<0.6% Cu) aluminum with integral cooling fins. Fastens to mounting plate with keyhole slots freeing both hands for securing and wiring. One stainless steel socket -head screw on each side of housing frees the reflector housing to rotate for aiming. Tightening the screws locks the two housings together with sealing provided by a silicone gasket. For visual aiming, adjustment may be accomplished with the fixture on. Lens Frame: One-piece die-cast, low copper alloy (<0.6% Cu) aluminum with integral hinges and stainless steel pins. Two stainless steel quarter -turn fasteners secure lens frame to reflector housing with sealing provided by a one-piece extruded and vulcanized silicone gasket. Lens is clear flat 3/1c," thick ternpered glass sealed to lens frame with a siliconegasket and retainer clips. For UP models, lens is mounted flush with frame for water run off, and is silicone sealed. Type 11,111, and IV Reflector Module: Specular Alzak' optical segments are rigidly mounted within a die-cast aluminum enclosure that attaches to the housing by a no -tool quick -disconnecting hinge and fastener. All sockets are porcelain medium base rated 4KV. All modules are factory prewired with a quick -disconnect plug for mating to the ballast. Available in three light distributions, all interchangeable within the same housing. Wall Grazer Reflector Module: Specular Alzak" optical segment is rigidly formed into a self-contained module which attaches to the housing by a no -tool quick -disconnecting hinge and fastener. Black louver vanes run parallel to the lamp arc for controlling the hot spot directly behind the fixture, and spill light into the atmosphere. All sockets are porcelain medium base rated 4KV. All modules are factory prewired with a quick -disconnect plug for mating to the ballast. Spot Reflector Module: Specular Alzak" optical spun parabola is rigidly mounted to a self-contained module which attaches to the housing by a no -tool quick -disconnecting hinge and fastener. Black internal louvers are provided to control the beam and prevent hot spots directly behind the fixture and spill light into the atmosphere. All sockets are porcelain medium base rated 4KV. All modules are factory prewired with a quick -disconnect plug for mating to the ballast. Electrical Components: High powerfactor ballasts are rigidly mounted inside the housing and are factory prewired with a quick -disconnect plug for mating to the socket. Starting temperatures are —40°F for HPS lamp modes and —20°F for MH and PMH lamp modes. Mounting Plate: Mounting plate attaches directly to any standard 4" junction box. All mounting plates are die-cast aluminum with reinforced ribs. Two studs are provided in each plate with flange nuts to allow fixture mounting by keyhole slots. Sealant must be applied (by others) between mounting plate and mounting surface to insure a dry junction box. Finish/Color: Super TGIC thermoset polyester powder coat paint, 2.5 mil nominal thickness, applied over a titanated zirconium conversion coating; A.S.T.M. 2500 hour salt spray test endurance rating. Standard colors are Black, Dark Bronze, Light Gray, Platinum Silver, or White. Custom colors are available. CAUTION: Fixtures must be grounded in accordance with national, state and/or local electrical codes. Failure to do so may result in serious personal injury. Listings and Ratings UL cUL 1598' — 25C Ambient IP66 Rated I CE ISO 9001:2000 'Suitable for wet locations KIM LIGHTING RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE. © 2006 KIM LIGHTING INC. • P.O- BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695 5608706213 WD14 �/� 14 Wall Director" MM LIGHTfNG revision 8/01/06 - wdl4.pdf Type: Job: Page: 2 of 5 Standard Features Fixture G� ,�� !� o 0 Cat. No. designates WD14 fixture, Up (U) or Down (D) configuration, and light WD Fixture distribution (2, 3, 4, G or S). Light Distribution: Type II Type III Type IV Wall Grazer Spot Cat. No.: (Up 141 C WD14U2 C WD14U3 ❑ WD14U4 ❑ WD14UG E WD14US Cat. No.: (Down 141 YWD14D2 C WD14D3 C WD14D4 -D WD14DG ` WD14DS Finish Color: Black Dark Bronze Light Gray Platinum Silver White 'Custom Colors Super TGIC powder coat Cat. No.: EL BL -PDB -P LG -P ElPS-P ElWH-P ElCC-P paint over a titanated X, zirconium conversion 'Custom colors subject to additional charges, minimum quantities and extended leadtimes. coating. Consult representative. Custom color description: © 2006 KIM LIGHTING INC. • P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 - TEL: 626/968-5666 - FAX: 626/369-2695 5608706213 �ok MM LIGHTING Type: Job: Pie Standard Features WD14 14" Wall Director revision 8/01/06 • wdl4.pdff Page: 3 of 5 Electrical Module Cat. Nos. for Electrical Modules available: PMH = Pulse Start Metal Halide MH = Metal Halide HPS = High Pressure Sodium PL = Compact Fluorescent Triple Tube IF =Induction Fluorescent O 5OPMH120' OPMH120` ; J� 100PMH120aCi 125PMH120' ❑ 15OPMH120' L15OPMH2O8' OPMH2O81 '`i 10OPMH2O8' ❑ 12513MH2Ow 015OPMH208' L 50PMH240' _' 70PMH2401 J IOOPMH240' ❑ 125PMH240' U 15OPMH240' L 5OPMH2774 .70PMH2771 J IOOPMH2774 L,' 125PMH277, L 150PMH2774 L! 50PMH3474 '_ 70PMH34r LI 10OPMH3471 L 15OPMH3474 70PMH480" �'� 10OPMH4803.1 ❑ 15OPMH4801,' Lam ED -17, Clear ED -17, Clear ED -17, Clear ED -17, Clear ED -17, Clear Socket Medium Base Medium Base Medium Base I Medium Base Medium Base ANSI Ballast M148, M110 1 M143, M98 M140, M90 IM150 1 M142, M102 ❑ 175MH120 ❑ 70HPS120 ❑ 100HPS120 ❑ 150HPS120 ❑ 175MH2O8 ❑ 70HPS208 ❑ 100HPS208 ❑ 150HPS208 ❑ 175MH240 ❑ 70HPS240 ❑ IOOHPS240 ❑ 150HPS240 ❑ 175MH277 0 70HPS277 ❑ 100HPS277 ❑ 150HPS277 ❑ 175MH347 ❑ 70HPS347 ❑ IOOHPS347 ❑ 150HPS347 Lamp Lamp Line Watts Type Volts — ❑ 175MH4803 El70HPS4803 ❑ 100HPS4801 ❑ 15OHPS480' Lamp ED -17, or ED -28 Clear T6 Clear G-12, ED -17 Clear ED -17 Clear T6 Clear, ED -17 Clear, or E-18 Clear 175 MH 277 Socket Medium Base G-12 Base, or Medium Base G12 Base,. Medium or Mogul Base Medium Base Base, or Mogul Base ANSI Ballast M-57 S-62 S-54 S-55 Lamp and electrical data supplied for reference ❑ 42PL1201 17 57PL1201.' ❑ 60PL1201.2 ❑ 70PL1201.2 ❑ 551F120 ❑ 42PL2081 ❑ 57PL2081' ❑ 60PL2081-1 ❑ 70PL2081-2 ❑ 551F208 purposes only. All initial lumen values shown may vary from one manufacturer to another. Consult lamp manufacturer's data for exact ❑ 42PL2401 ❑ 57PL2401.2 [1 60PL2401-2 ❑ 70PL2401.2 ❑ 551F240 ❑ 42PL2771 ❑ 57PL2771.2 --] 60PL2771.2 ❑ 70PL2771.2 ❑ 551F277 Lamp Coated Coated Coated Coated Induction Socket I GX24 -4 Base GX24 -5 Base 2GB-1 Base I GX24 -6 Base ANSI Ballast lumen and life data. NOTE: For lamp/ballast 'Multiple CFL lamp configurations (ie, two 42W lamps) are possible with certain optical information outside of the systems. Consult factory for details. U.S.A. and Canada, please 2 Remote battery and test switch available for 57W, 60W, and 70W CFL lamps - consult consult your local Kim pack factory. "EM" option not available with 85W CFL, 55W IF, or 85W IF lamps. representative. '480 volt with medium base lamp sockets may require approval by the local building code authority. 'CAUTION: All manufacturers of metal halide lamps recommend turning them off for 15 minutes once per week when under continuous operation. This will reduce the risk of arc tube rupture at end of life. Also, color temperature may differ between manufacturers of metal halide lamps. See lamp manufacturers' specification sheets. WARNING: Fixtures must be installed and grounded in accordance with national, state and/or local electrical codes. Failure to do so may result in serious personal injury. For lamp/ballast information outside of the U.S.A. and Canada, please consult your local Kim representative. Lamps by others. © 2006 KIM LIGHTING INC. • P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 • TEL: 626/968-5666 • FAX: 626/369-2695 5608706213 WD Type II 70 Watt Metal Halide ED -17, Clear, Medium Base 5040 Initial Horizontal Lumens 3780 Mean Horizontal Lumens ANSI Code M98SJ-70 I.T.L. Test No. 41482 Each chart is a typical half. Tilt 0 O A 1 Initial Vertical and Horizontal Tilt B 2 Footcandles at Listed C D E\ 3 4 Mounting Heights M F 1 H 5 I 8' 10' 12' 14' 16' Lateral Distance N Wall A 16 8.2 4.7 3.0 2.0 in Mounting 2 0 Mounting B 8.0 4.1 2.4 1.5 1.0 Heights g p �g� Q C 4.0 2.0 1.2 .75 .50 3 Q 0 D 1.6 .82 .47 .30 .20 4 R w E .80 .41 .24 .15 .10 S > F .40 .20 .12 .07 .05 G .16 .08 .05 .03 .02 5 T H .08 .04 .02 .01 .01 0 Ground or 1 Ceiling* M 8.0 5.1 3.6 2.6 2.0 Longitudinal 2 N 4.0 2.6 1.8 1.3 1.0 Q Distance in Mounting Heights 3 z O 2.0 1.3 .89 .65 .50 p P .80 .51 .36 .26 .20 4 " I Q .40 .26 .18 .13 .10 p R .20 .13 .09 .07 .05 5 = S .08 .05 .04 .03 .02 5 T .04 .03 .02 .01 .01 Tilt B 2 c p 3 M E F 4 1 G H 5* For UP applications, simply visualize N Lateral Distance Wali \I ` the charts as being inverted with the in Mounting 2 0 . Mounting ground plane becoming the ceiling. Heights Height 3 P � Q FWall iling 4 R 5 S 0 Ground or T Ceiling* Longitudinal \ Distance in Mounting Heights 10"I 0 1 Longitudinal 2 Distance in Mounting Heights 6 K I M LIGHTING Mounting Height CHINA WALL MOUNT Wet Location Listed Job: ,KK y PART # Description I Voltage I Finishes I Options and Visual Descriptive CHWO011CF42 42w Compact Fluorescent CHW0011MH70 70w Metal Halide CHWO011IN150 150w Incandescent CF/MH Lamp Included 1 120V F05 White 2 277V F09 Pewter 3 347V F13 Forest Green *Consult TMS F15 Matte Black F16 Gloss Black F19 Mirror Silver F21 Architectural Bronze F24 Melted Platinum F29 Verde Includes G1 Globe Optional Wire Guard - GR 275 8 PART # Voltage Finishes Options Quantity G�Lu Vol MA -10 I?X.7 V 1C-1�1 Note: *Fixture Reflector, Gooseneck Armand Cover Plate is in choosen Finish unless specified -consult TMS. Coll s�a CHIN A Size and specification subject to change; refer to website for updated information. All lighting products are UL & CSA listed. usreo � �s IES INDOOR REPORT PHOTOMETRIC FILENAME: V-180F0570MH.IES DESCRIPTION INFORMATION (From Photometric File) IESNA: LM -63-1995 [TEST] Photopia 2.0.0.17 PHOTOMETRIC REPORT [MANUFAC]TMS LIGHTING [LUMINAIRE] V-180 [LUMCAT] V-180F057OMH [LAMP] 70W MH CHARACTERISTICS Total Rated Lamp Lumens 5600 Total Luminaire Efficiency 62.4% CIE Type Semi -Direct Spacing Criteria (0-180) 1.64 Spacing Criteria (90-270) 1.60 Spacing Criteria (Diagonal) 1.70 Basic Luminous Shape Rectangular Luminous Length (0-180) 1.33 ft Luminous Width (90-270) 1.33 ft Luminous Height 0.00 ft LUMINANCE DATA (cd/sq.m) Angle In Average Average Average Degrees 0 -Deg 45 -Deg 90 -Deg 45 4910 5088 5162 55 6010 6097 6055 65 7407 7159 7189 75 5202 5092 5247 85 17185 16221 16933 Photometric Toolbox32 (c) copyright 1995-2003 by Lighting Analysts, Inc. Page 1 Calculations based on published IES Methods and recommendations. Results derived from content of manufacturers IES format photometric file. IES INDOOR REPORT PHOTOMETRIC FILENAME: V-180F057OMH.IES CANDELA TABULATION Photometric Toolbox32 (c) copyright 1995-2003 by Lighting Analysts, Inc. Page 2 Calculations based on published IES Methods and recommendations. Results derived from content of manufacturers IES format photometric file. 0 22.5 45 67.5 90 112.5 135 157.5 180 0 603.57 603.57 603.57 603.57 603.57 603.57 603.57 603.57 603.57 5 614.62 599.64 577.63 569.45 562.75 646.83 578.06 612.38 537.9 10 559.68 591.92 620.73 606.7 .632.87 585.25 612.41 634.42 638.35 15 596.94 599.41 610.96 616.54 608.19 614.86 645.91 631.95 588.82 20 598.39 610.33 661.48 611.95 617.17 647.13 619.61 624 620.23 25 631.45 622.91 676.2 626.17 650.1 641.88 631.85 644.46 643 30 669.44 629.11 649.44 663 616.41 639.37 647.29 677.13 648.22 35 643.93 628.19 659.77 641.35 638.42 635.81 623.47 657.99 640.03 40 644.89 619.71 632.05 608.09 619.11 611.06 618.49 628.25 616.18 45 573.94 594.59 594.73 610.37 603.44 598.16 585.12 590.93 620.07 50 583.77 576.05 570.64 596.21 586.71 575.65 573.47 573.77 589.78 55 569.88 569.71 578.09 574.53 574.13 556.12 573.64 579.55 603.77 60 515.79 525.06 533.15 542.02 537.8 537.73 531.23 525.49 550.41 65 517.51 491.96 500.15 510.01 502.29 499.88 500.71 498.83 515.72 70 383.92 371.91 386.03 382.7 399.86 369.07 379.37 377.35 368.51 75 222.58 222.22 217.87 217.01 224.5 225.16 216.45 219.09 230.11 80 194.3 205.26 207.44 214.33 202.26 201.2 205.89 209.55 210.64 85 247.6 244.43 233.71 256.77 243.97 237.86 242.88 254.2 254.13 90 231.59 226.64 242.05 229.32 236.91 236.35 234.66 242.71 231.89 95 248.72 231.07 232.81 247.2 240.4 237.04 254.66 247.07 245.65 100 225.52 218.26 218.46 227.8 227.9 234.63 236.21 228.85 246.38 105 190.77 174.97 176.09 169.36 173.22 182.79 182.39 178.27 177.51 110 119.46 115.63 117.31 112.5 119.03 111.14 111.44 117.02 117.12 115 52.87 55.24 54.09 59.89 55.93 58.24 59.5 54.48 62.11 120 42.73 43.63 46.27 .39.93 42.83 48.58 40.82 45.11 45.44 125 38.11 36.93 38.25 43.96 36.99 36.89 39.01 39.8 36.13 130 34.25 36.17 33.59 31.28 31.61 36.07 33.56. 39.4 37.16 135 30.79 29.67 29.11 31.22 26.53 29.14 28.97 29.47 28.54 140 23.46 25.67 24.16 23.92 26.37 27.62 24.39 25.34 24.58 145 25.97 27.55 23.17 24.58 20.72 22.93 24.22 21.68 23.4 150 21.94 18.97 21.58 17.03 19.96 15.91 20.92 18.68 15.08 155 14.22 15.84 13.03 15.94 13.5 15.34 16 13.03 12.01 160 9.8 8.48 11.09 8.74 17.32 11.52 9.21 9.87 8.74 165 9.57 10.53 7.89 6.63 6.8 8.91 9.31 6.14 7.75 170 7 3.4 6.8 4.03 5.64 6.43 7.82 9.37 6.1 175 2.57 0.73 5.28 2.44 0.89 0.89 0.89 3.3 8.12 180 0 0 0 0 0 0 0 0 0 Photometric Toolbox32 (c) copyright 1995-2003 by Lighting Analysts, Inc. Page 2 Calculations based on published IES Methods and recommendations. Results derived from content of manufacturers IES format photometric file. IES INDOOR REPORT PHOTOMETRIC FILENAME: V-180F0570MH.IES ZONAL LUMEN SUMMARY Zone Lumens %Lamp %Fiat 0-30 528.08 9.4 15.1 0-40 928.33 16.6 26.6 0-60 1898.43 33.9 54.3 0-90 2899.57 51.8 83 90-120 511.9 9.1 14.7 90-130 546.91 9.8 15.7 90-150 584.33 10.4 15.7 90-180 593.94 10.6 17 0-180 3493.51 62.4 100 Total Luminaire Efficiency = 62.4% ZONAL LUMEN SUMMARY Zone Lumens 0-10 57.23 10-20 174.91 20-30 295.94 30-40 400.25 40-50 463.24 50-60 506.86 60-70 475.34 70-80 271.48 80-90 254.32 9.0-100 258.57 100-110 185.25 110-120 68.09 120-130 35.01 130-140 22.99 140-150 14.43 150-160 6.87 160-170 2.4 170-180 .34 Photometric Toolbox32 (c) copyright 1995-2003 by Lighting Analysts, Inc. Page 3 Calculations based on published IES Methods and recommendations. Results derived from content of manufacturers IES format photometric file. IES INDOOR REPORT PHOTOMETRIC FILENAME: V-180F057OMH.IES COEFFICIENTS OF UTILIZATION -ZONAL CAVITY METHOD Effective Floor Cavity Reflectance 0.20 RC 80 70 50 30 10 0 RW 70 50 30 10 70 50 30 10 50 30 10 50 30 10 5030 10 0 0 72 72 72 72 69 69 69 69 63 63 63 58 58 58 54 54 54 52 1 64 60 57 54 61 57 54 52 53 50 48 48 46 45 44 43 42 39 2 57 51 46 42 54 49 44 41 45 41 38 41 38 36 38 35 33 31 3 51 44 38 34 49 42 37 33 39 35 31 36 32 29 33 30 27 25 4 47 39 33 28 44 37 31 27 34 29 26 31 27 24 29 25.23 21 5 43 34 28 24 40 33 27 23 30 25 22 28 24 20 25 22 19 18 6 39 30 24 20 37 29 24 20 27 22.19 25 21 18 23 19 17 15 7 36 27 21 17 34 26 21 17 24 20 16 22 18 15 21 17 14 13 8 33 25 19 15 32 24 18 15 22 17 14 20 16 13 19 15 13 11 9 31 22 17 13 30 22 17 13 20 16 13 19 15 12 17 14 11 10 10 29 21 15 12 28 20 15 12 18 14 11 17 13 11 16 13 10 9 Photometric Toolbox32 (c) copyright 1995-2003 by Lighting Analysts, Inc. Page 4 Calculations based on published IES Methods and recommendations. Results derived from content of manufacturers IES format photometric file. IES INDOOR REPORT PHOTOMETRIC FILENAME: V-180170570MH.IES POLAR GRAPH Maximum Candela = 677.13 Located At Horizontal Angle = 157.5, Vertical Angle = 30 # 1 - Vertical Plane Through Horizontal Angles (90 - 270) # 2 - Vertical Plane Through Horizontal Angles (0 - 180) # 3 - Horizontal Cone Through Vertical Angle (0) Photometric Toolbox32 (c) copyright 1995-2003 by Lighting Analysts, Inc. Page 5 Calculations based on published IES Methods and recommendations. Results derived from content of manufacturers IES format photometric file. r 1 Catalog Number OFA L/THON/A L/OAMWO' Notes Type ' FEATURES & SPECIFICATIONS INTENDEDUSE Ideal for parking areas, street lighting,walkwaysand car lots. CONSTRUCTION Rugged, die- cast soft comer aluminum housing with 0.1 2"nominal wallthic kness. Extruded iV'softcornerarmfor pole orwall mounting is standard. Die-castdoorframe has impact - resistant, tempered, glass lensthatisfully gasketed with one -pie cetubularsilicone. FINISH Standard finish is dark bronze (DDB) polyester powderfinish,with other architectural colors available. OPTICALSYSTEM Anodized, aluminumhydroformed reflectors:IESfull cutoff distributions R2 (asymmet- ri c), R3 (asymmetric), R4 (forward throw) and R5S (square). High-performance anodized, segmented aluminum reflectors I ES full cutoff distributions SR2 (asymmet- ri c), S R3 (asymmetric) and SR4SC (forwardthrow, sharp cutoff). Segmented reflectors attach withtool-less fasteners and are rotatable and interchangable. ELECTRICAL SYSTEM High reactance, high powerfactorballastfor100W/15OW. Constant -wattage autotransformerfor 175-400W. Super CWA Pulse Start ballast requiredfor200W,320W and350W (mustorderSCWAoption). Ballastis copper -wound and 100% factory -tested. Porcelain, horizontal, position -oriented, socketwith copper alloy, nickel -plated screw shell and center contact Medium- base socket used with 100W & 150W, mogul- base socket used with 175-400W. UL listed 1500W -600V. LISTING UL Listed (standard). CSA Certified (see Options). ULlistedforwetlocations. IP65 rated in accordancewith standard IEC529. CONTOUR o S E R I E S Specifications EPA: 1.2 ftz Weight: 41 lbs (18.6 kg) Length: 17-1/2" (44.5 cm) Width: 17-1/2" (44.5 cm) Depth: 7-1/8" (18.1 cm) ORDERING INFORMATION Choose the boldface catalog nomenclature that best suits your needs and write it on the appropriate line. Ord r acc ssorseparatepatalo number. KAD Series Wattage Voltage Mounting KAD 100M 1111 SPD04 Square pole (4"arm) 150M 2081 (standard) 175M 240P SP009 Square pole (9"arm)5 200M 277 RPD04 Round pole (4"arm) 2W yp RPD09 Round pole (9"arm)5 331W 03 WWD04 Wood pole orwall(4"arm) 35M TW WWO09 Wood pole orwallIT 400Mt arm)5.6 WBD04 Wallbracket(4"arm)s Distribution WBD09 Wallbracket(9"arm)a L/Ann (When ordering KMA, Hydroformed reflectors DAD12) R2 IEStype II asymmetricz Shipped separately R3 IEStypeIII asymmetricz KMA Mastarmadapter R4 IES type IVforward throwz KTMB Twinmountingbar R5S IEStypeVsquare DA012P Degreearm(pole) Seamented reflectors DA012WB Degreearm(wall) SR2 IEStype I I asymmetricz SR3 IEStype 11 l asymmetricz SR4SC IES type lVforward throw NOTES: 1 Reduced jacket ED28 lamp must be used with SR2, SR3 & SR4SC optics. 2 House -side shield available. 3 Consut factory for availability in Canada. 4 Optional multi -tap ballast (120, 208, 240, 277V). 5 The SPD09, RPD09 or WWD09 must be used when two or more luminaires are oriented on a 90° drilling pattern. 6 May be ordered as accessory. 7 QRSTD available in select wattages; consult factory. 8 Additional architectural colors available; please see Architectural Colors brochure, Form No. 794.3. 9 Must use RP009. 10 Only available with SR2, SR3, and SR4SC optics. Soft Square Cutoff Lighting KAD METAL HALIDE 100W-40OW 20' to 35' Mounting _T 7-1/8" I— 4" 17-1/2' Example: KAD 400M R2120 SPD04 LPI Accessories. Tenon Mounting Slipfitter Options Shipped installgd in fixture KADVG Vandalguard SF Single fuse 020,277,347V,n/aTB) KADWG Wireguard OF Double fuse (208,240,480V,n/aTB) KAOWBA Decorativewall PER NEMAtwist-lock receptacle bracket only (no photo control) Architecturalcolors9 LPI Lamp includedasstandard Standard colors ULP Lesslamp DDB Darkbronze PD PowerTrayto (standard) WFB Terminal WiringBlock10 DWH White ORS Quartz restrike system (250W DBL Black maximum,lampnotincluded)7 Classic colors CSA CSA Certified DMB Mediumbronze SCWA Super CWA Pulse Sta rt Ballast DNA Naturalaluminum (n/a 100W & 175W) DSS Sandstone Shjpoedse arp atelus DGC Charcoalgray PEI NEMAtwist-lock PE 0 20,208,24OV) DTG Tennisgreen PE3 NEMAtwist-lockPE(347V) DBR Brightred PE4 NEMAtwist-lockPE(480V) DSB Steel blue PE7 NEMAtwist-lockPE(277V) . HS House -side shield (R2,R3, 114) (SR2, SR3) Accessories. Tenon Mounting Slipfitter Outdoor Sheet #: KAD-M AL -370 Order as separate catalog number. Number of fixtures Tenon O.D. One Two®180° Two®90° Three®120° Three®90° Four@90° 2-3/8' T20-190 T20-280 T20-2901 T20-3201 T20-3901 T2DA901 2-7/8' T25-190 T25-280 T25-2901 T25-320 725.3901 725AW 4- 735-190 T35-280 T35-2901 T35-320 T35-3909 735AW Outdoor Sheet #: KAD-M AL -370 FEATURES Type OPTICAL SYSTEM • Aluminum upper reflector coated with highly reflective white paint provides high efficiency and an. evenly illuminated aperture appearance. • Available with tempered prismatic lens (T73), flat Fresnel lens (FFL) or flat opal lens (FOL). • Reressed white door (RW) or stepped black baffle (SK are available with white painted flange provided • Door is retained by self -aligning, torsion suandpport springs, preventing gaps between door ceiling. MECHANICAL SYSTEM • 16 -gauge galvanized steel mounting/plaster frame with integral brackets to retain optical system. Maximum 1-1/2" ceiling thickness. • 16 -gauge galvanized steel mounting bars with continuous 4" vertical adjustment are shipped pre- installed. Post installation adjustment possible without the use of tools from above or below ceiling. • Galvanized steel junction box with hinged access covers and spring latch. Two combination 1/2"-3/4" and four 1/2" knockouts for straight -through conduit runs. Capacity: 8 (4 in, 4 out) No. 12 AWG conductors rated for 90°C.. ELECTRICAL SYSTEM • Die-cast aluminum lampholder housing. • Medium -base porcelain socket with nickel -plated screw shell. • Prewired encased -and -potted, 120/277 or 120/347 ballast tray module. Module can be attached before or after mounting of mounting/plaster frame. • Thermally -activated insulation detector. LISTING • Fixtures are t1L Listed for thru-branch wiring, Non -IC recessed mounting and wet locations. Listed and labeled to.comply with Canadian Standards. Catalog number HID Downlights 811 LGH Round Lens Wet Location 11 Metal Halide Lamp Aperture: 7-7/8 (20.1) Ceiling Opening: 8-7/8 (22.5) Overlap Trim: 9-1/4 (23.5) 20-1/4 (51.4) 17-3/4. (45.1) Example: LGH 150M 8RW T73.120 All dimensions areinches (centimeters). ORDERING INFORMATION Options Choose the boldface catalog nomenclature that best suits your needs and write it on the appropriate line. Order accessories as separate catalog numbers (shipped separately). LGH "r Series Watta a/Lam ' Door Frame Shielding Volta e LGH Metal Halide 8RW Regressed T73 Tempered 120 SOM 5OW ED17 white door prismatic lens 277 70M 70W ED17 8SB Stepped FFL Flat Fresnel lens 347 100M 10OW ED17 black baffle FOL Flat opal lens 150M 150W ED17 required Color -Corrected Metal Halide Quartz Restrike System. 50MHC 5OW ED17 Quartz Restrike System with time 70MHC 70W ED17 delay 100MHC 10OW ED17 Emergency Circuit 15OMHC 150W ED17 Single Fuse WLP Accessories NOTES Order as separate catalog number. 1 Recommended for use with coated lamps. SCAB Sloped ceiling adapter 2 For compatible Reloc systems, refer to Technical Bulletins tab. EC. Degree of slope must be 3 Not available with QRSTD or 4 Not available with QRS or EC. specified (10D, 15D, 20D, 5 Not available with QRS or QRSTD. 25D, 30D). Ex: SCAB 10D. 17-3/4. (45.1) Example: LGH 150M 8RW T73.120 got h a M. GOTHAAI ARCHITECTURAL DOWNLIGHTING 1400 Lester Road Conyers Georgia 30012 i P 800 315 4982 F 770 860 3129 LGH 8 DHID-500 AnW cufty&&xfsCa o&v www.gothamlighting.com Options CP Chicago Plenum TRDA Tamper -Resistant Door Assembly LRCI Provides compatibility with Lithonia Reloc@ System. Lithonia Reloc System can be installed less this option with connectors provided by others. Access above ceiling required QRS' Quartz Restrike System. QRSTD" Quartz Restrike System with time delay ECS Emergency Circuit SF Single Fuse WLP Lamp gasketing, ships uninstalled got h a M. GOTHAAI ARCHITECTURAL DOWNLIGHTING 1400 Lester Road Conyers Georgia 30012 i P 800 315 4982 F 770 860 3129 LGH 8 DHID-500 AnW cufty&&xfsCa o&v www.gothamlighting.com 8" LGH Open Reflector Distribution curve Distribution data Output data Coefficient of utilization Illuminance Data at 30 Above Floor for Nib t4,9- a Single luminaire LGH 100M 8RW Average 7 lamp, 1.0 s/mh, 7900 rated lumens, Test no. LTL14368 10^ ` I nital fc fc at f[ at Mount at beam pf beam Beam 20% height center diameter edge From O° Ave Lumens Zone Lumens %Lamp pc 80% 70% 50% BO* 0 2599 4.6 0° - 30° 1841.8 23.3 pw 50% 30% 50% 30% 50% 30% 700 5 2576 244 0° - 40' 2713.2 34.3 1 .56 .54 .55 .53 .53 .52 15 2424 680 0° - 60° 3765.2 47.7 2 .51 .48 .50 .47 .48 .46 60° 25 2014 918 0°-90° 4130.0 '52.3 3 .46 .42 .45 .42 .44 .41 35 1395 871 901- 180° 0.0 0.0 4 .42 .38 .41 .37 .40 .37 50° 45 833 647 0°-180° 4130.0 '52.3 5 .38 .34 .37 .34 .36 .33 55 446 405 'E fnciency 6 -35 .31 .34 .31 .33 .30 65 238 237 7 .32 .28 .32 .28 .31 .28 40° 75 91 103 8 .30 .26 .29 .26 .29 .25 85 22 25 9 .28 .24 .27 .24 .27 .23 90 0 10 .26 .22 .25 .22 .25 .22 LGH 100M 8RW FFL, 10OW ED17 lamp, 1.0 s/mh, 7900 rated lumens, Test no. LTL14369 pf 20% From 00 Ave Lumens Zone Lumens % Lamp pc 80% 70% 50% 0 2837 0° - 30° 1894.0 24.0 pw 50% 30% 50% 30% 50% 30% 5 2794 265 0° - 40° 2647.9 33.5 1 .54 .52 .53 .51 .51 .49 15 2641 733 0° - 60° 3612.6 45.7 2 .49 .46 .48 .45 .46 .44 25 1964 896 0° - 90° 3936.2 49.8 3 .44 .41 .43 .40 .42 .39 35 1198 754 90° - 180° 0.0 0.0 4 .40 .37 .39 .36 .38 .35 45 731 568 0°-180° 3936.2 '49.8 5 .37 .33 .36 .33 .35 .32 55 442 396 'Efficiency 6 .34 .30 .33 .30 .33 .29 65 220 220 7 .31 .28 .31 .27 .30 .27 75 75 83 8 .29 .25 .29 .25 .28 .25 85 18 20 9 .27 .23 .27 .23 .26 .23 90 0 10 .25 .22 .25 .22 .25 .22 Average LGH 150M BRW T73, 150W ED17 lamp, 1.1 s/mh, 12000 rated lumens, Test no. LTL14192 pf 20% From 0° Ave Lumens Zone Lumens % Lamp pc 80% 70% 50% 0 3846 0° - 30° 2795.4 23.3 pw 50% 30% 50%30% 50% 30% 5 3823 362 0° - 400 4170.9 34.8 1 .56 .54 .55 .53 .53 .51 15 3629 1020 0° - 60' 5766.1 48.1 2 .50 .48 .50 .47 .48 .46 25 3098 1414 0°-90° 6222.2 51.9 3 .46 .42 .45 .42 .43 .41 35 2207 1376 90° - 180° 0.0 0.0 4 .42 .38 .41 .37 .40 .37 45 1309 1013 0° - 180° 6222.2 '51.9 5 .38 .34 .37 .34 .36 .33 55 .639 583 `Efficiency 6 .35 .31 .34 .31 .33 .30 65 299 302 7 .32 .28 .32 .28 .31 .28 75 111 124 8 .30 .26 .29 .26 .29 .25 85 26 31 9 .28 .24 .27 .24 .27 .23 90 0 10 .26 .22, .25 .22 .25 .22 LGH 150M 8RW FFL, 150W ED17 lamp, 1.0 s/mh, 12000 rated lumens, Test no. LTL14193 pf 20% From 0° Ave lumens Zone Lumens % Lamp pc 80% 70% 50% 0 3994 0° - 30° 2896.4 24.1 pw 50% 30% 50% 30% 50% 30% 5 3969 380 0° - 40° 4205.9 35.0 1 .58 .57 .57 .55 .55 .54 15 3911 1090 0° - 60° 5933.6 49.4 2 .52 .50 .51 .49 .50 .47 25 3125 1426 0° - 90' 6506.8 54.2 3 .47 .44 .47 .43 .45 .42 35 2091 1309 90° - 180° 0.0 0.0 4 .43 .39 .42 .39 .41 .38 45 1315 1021 0° - 180° 6506.8 '54.2 5 .39 .35 .39 .35 .38 .34 55 787 707 'E friclency 6 .36 .32 .35 .32 .35 .31 65 387 388 7 .33 .29 .33 .29 .32 .28 75 135 149 8 .31 .27 .30 .26 .30 .26 85 32 36 9 .28 .25 .28 .24 .28 .24 90 0 10 .27 .23 .26 .23 .26 .22 50% beam angle 10% beam angle 54.9° 92.2° 50% beam angle 10% beam angle 50.9° 88.11 I nital fc fc at f[ at Mount at beam Beam beam Beam beam height center diameter edge diameter edge 8 85.9 5.7 43.0 11.4 8.6 10 46.2 7.8 23.1 15.6 4.6 12 28.8 9.9 14.4 19.8 2.9 14 19.7 12.0 9.8 23.9 2.0 16 14.3 14.0 7.1 28.1 1.4 50% beam angle 10% beam angle 50.9° 88.11 50% beam angle 10% beam angle 56.6° 93.1° Inital fc fc at fc at Mount atbeam Beam beam Beam beam height center diameter edge diameter edge 8 93.8 5.2 46.9 10.6 9.4 10 50.4 7.1 25.2 14.5 5.0 12 31.4 9.0 15.7 18.4 3.1 14 21.5 10.9 10.7 22.3 2.1 16 15.6 12.8 7.8 26.1 1.6 50% beam angle 10% beam angle 56.6° 93.1° 50% beam angle 10% beam angle 54.9° 93.1° Inital fc fc at fc at Mount at beam Beam beam Beam beam height center diameter edge diameter edge 8 127.1 5.9 63.6 11.6 12.7 10 68.4 8.1 34.2 15.8 6.8 12 42.6 10.2 21.3 20.1 4.3 14 29.1 12.4 14.5 24.3 2.9 16 21.1 14.5 10.6 28.5 2.1 50% beam angle 10% beam angle 54.9° 93.1° NOTES: 1. For electrical characteristics consult Technical Bulletins tab. 2. Tested to current IES and NEMA standards under stabilized laboratory conditions. Various operating factors can cause differences between laboratory data and actual field measurements. Dimensions and specifications are based on the most current available data and are subject to change without notice. GOTHAM ARCHITECTURAL DOWNLIGHTING DHID-500 1400 Lester Road Conyers Georgia 30012 32005 Gotham, Rev. 12/05 of h a m P 800 315 4982 F 770 860 3129 DHID-500.p65 b www.gothamlighting.com An-lculryamands Cnmaany Inital fc fc at fc at Mountatbeam Beam beam Beam beam height center diameter edge diameter edge 8 132.0 5.7 66.0 11.6 13.2 10 71.0 7.8 35.5 15.8 7.1 12 44.3 9.9 22.1 20.0 4.4 14 30.2 12.0 15.1 24.3 3.0 16 21.9 14.0 11.0 28.5 2.2 NOTES: 1. For electrical characteristics consult Technical Bulletins tab. 2. Tested to current IES and NEMA standards under stabilized laboratory conditions. Various operating factors can cause differences between laboratory data and actual field measurements. Dimensions and specifications are based on the most current available data and are subject to change without notice. GOTHAM ARCHITECTURAL DOWNLIGHTING DHID-500 1400 Lester Road Conyers Georgia 30012 32005 Gotham, Rev. 12/05 of h a m P 800 315 4982 F 770 860 3129 DHID-500.p65 b www.gothamlighting.com An-lculryamands Cnmaany KAD 400M Arm -mounted Soft Square Cutoff Coefficient of Utilization Initial Footcandles S;l Ski L�� KAD R2 Test no. 1193083101 Line current Primary 040902 KAD �COEFFIC`IENTOF (Amps) dropout Input Power Regulation Wattage/ballast voltage COEFFICIENT OF UTILIZATION voltage watts factor (%) Line V = Lamp lumens 120 LIZATION 55 400CWA 208 1.45/2.30 0 .1 .2 .3 .4 .5 .6 1.25/2.00 0 .1 .2 .3 .4 .5 .6 2 Autotransformer 277 1.10/1.75 125 480 2 225 1 s i s x 0 o Z Z 0 Z z z _ 5 1 0 0 5 2.5 1 o 0 2.5 1 Z 1 Z 0.5 2 0.5 2 0,25 0.2 0.1., 3 Z y O.t 3 Z 4 O L 4 _y � 0 1 2 3 4 5 6 0 1 2 3 4 5 6 40OW Metal Halide lamp, 32,000 rated lumens, 40OW Metal Halide lamp, 32,000 rated lumens, Footcandle values based on 30' mounting height, Footcandle values based on 30' mounting height, Distribution Type II, cutoff. Distribution Type III, cutoff. KAD R4 Test no. 1191110101 KAD RMS Test no. 1192061101 KAD R5S Test no. 1193111901 COEFFICIENT OF UTILIZATION COEFFICIENT OF UTILIZATION COEFFICIENT OF UTILIZATION 0 .1 .2 .3 .4 .5 .6 0 .1 .2 .3 .4 .5 .6 0 .1 .2 .3 .4 .5 .6 2 2 2 x x x c' x 1 x x A Z Z > 0 Z z Z > 0 z Z F 5 1 i 5 1 5 2.5 1 2.50 2.5 0 1 o 2 z 1 2 � z 0.5 2 � z 1 0.5 Z 0.25 Z 0.25 0.1 z 0.2 0.1 3z � y 0. 3 z r y 3 z ra- y 4 4 4 0 1 2 3 4 5 6 0 1 2 3 4 5 6 0 1 2 3 4 5 6 40OW Metal Halide lamp, 32,000 rated lumens, 40OW Metal Halide lamp, 32,000 rated lumens, 40OW Metal Halide lamp, 32,000 rated lumens, Footcandle values based on 30' mounting height, Footcandle values based on 30' mounting height, Footcandle values based on 30' mounting height, Distribution Type IV, cutoff. Distribution Type IV, cutoff. Distribution Type V, cutoff. Electrical Characteristics Tested to current IES and NEMA standards under stabilized laboratory conditions. Various operating factors can cause differences between laboratory data and actual field measurements. Dimensions and specifications on this sheet are based on the most current available data and are subject to change without notice. Notes: 1 Photometric data for other distributions can be accessed from www.lithonia.com. OrA L/THON/A L/GHT/NGS An ,%WuiiyBrands Company Sheet #: KAD-M © 2000 Acuity Lighting Group, Inc., Rev. 12/8/06 Mounting Height Correction Factor (Multiply the fc level by the correction factor) 25 ft. = 1.44 35 ft. =0.73 40 ft. =.56 / Existing Mounting Height 12_ Correction Factor New Mounting Height J n NIGHTTIME FRIENDLY Consistent with LEEDr goals 8 Green Globes' criteria for light pollution reduction Lithonia Lighting Outdoor One Lithonia Way, Conyers, GA 30012 Phone: 770-922-9000 Fax: 770-918-1209 www.lithonia.com Line current Primary Primary (Amps) dropout Input Power Regulation Wattage/ballast voltage Start/Operating voltage watts factor (%) Line V = Lamp lumens 120 2.50/4.00 55 400CWA 208 1.45/2.30 95 Peak -lead 240 1.25/2.00 110 455 90+ ±10% = ±10% Autotransformer 277 1.10/1.75 125 480 .73/1.00 225 Tested to current IES and NEMA standards under stabilized laboratory conditions. Various operating factors can cause differences between laboratory data and actual field measurements. Dimensions and specifications on this sheet are based on the most current available data and are subject to change without notice. Notes: 1 Photometric data for other distributions can be accessed from www.lithonia.com. OrA L/THON/A L/GHT/NGS An ,%WuiiyBrands Company Sheet #: KAD-M © 2000 Acuity Lighting Group, Inc., Rev. 12/8/06 Mounting Height Correction Factor (Multiply the fc level by the correction factor) 25 ft. = 1.44 35 ft. =0.73 40 ft. =.56 / Existing Mounting Height 12_ Correction Factor New Mounting Height J n NIGHTTIME FRIENDLY Consistent with LEEDr goals 8 Green Globes' criteria for light pollution reduction Lithonia Lighting Outdoor One Lithonia Way, Conyers, GA 30012 Phone: 770-922-9000 Fax: 770-918-1209 www.lithonia.com N € I I a ?� 21Schwan's �; DESIGN DEVELOPMENT Consumer Brands Warehouse & Distribution Facility E Watertower St Meridian, Idaho fwm�, Schwan's Consumer Brands DESIGNWarehouse & Distribution Facility ��� DEVELOPMENT E Watertower St Meridian, Idaho El as T I I a � o Schwan's Consumer Brands DESIGNWarehouse & Distribution Facility ��� DEVELOPMENT E Watertower St Meridian, Idaho 55749 1 I I I I I I I ' I I 1 I I I D li�oownvv'�`tAf!�o Slitv�tiu. January 22, 2007 TO: Jeffrey King- CTA Architects 1185 Grove St. Boise, ID 83702 SUBJECT: MCZC-06-218 Schwan's Distribution 1260 E. Watertower Ln. John S. Franden, President Rebecca W. Arnold, Vice President Sherry R. Huber, Commissioner David Bivens, Commissioner Carol A. Mckee, Commissioner xkipa `TET. JAN 2 4 2007 City of Meridian City Clerk Office On 2-28-2001, the Ada County Highway District Commissioners acted on for Murdoch Subdivision No. 2. The conditions and requirements also apply to MCZC-06-218. • Prior to final approval you will need to submit plans to the ACHD Development Review Department. • A traffic impact fee will be assessed by ACHD and will be due prior to the issuance of a building permit. Contact ACHD Planning & Development Services at 387-6170 for information regarding impact fees. If you have any questions or concerns please feel free to contact this office at (208) 387-6177. Sincerely, AOkfjrc Chelsee Kucera Planning Intern Right -of -Way and Development Services CC: Project File Lead Agency: Schwan's Consumer Brands Ada County Highway District • 3775 Adams Street • Garden City, ID • 83714 • PH 208-387-6100 • FX 345-7650 • www.achd.ada.id.us ADA COUNTY HIGHWAY DISTRICT Planning and Development Division Development Application Report Preliminary Plat — Murdoch #2/MPP-01-004 Locust Grove Road/Watertower Lane The application has been referred to ACHD by the City of Meridian for review and comment. Murdoch #2 is an 11 -lot office/residential subdivision on 20.3 -acres. The site is located on the west side of Locust Grove Road approximately 1,300 -feet south of Franklin Road. This development is estimated to generate 500 additional vehicle trips per day based on the existing zoning of R-8. On March 8, 2000, the ACHD Commission reviewed this site as MAZ-00-005, a rezone from RT to R-8. Roads impacted by this development: Locust Grove Road Watertower Lane Adkins Street Franklin Road ACHD Commission Date — February 28, 2001 — 6:30 p.m. Facts and Findings: Murdoch #2.cmm Page 1 A. General Information --------- Deleted,¶ Owner — Howell -Murdoch Development Applicant — JUB R-8 - Existing zoning (residential) 20.3 - Acres 11 - Proposed building lots 2 - Proposed common lots 1,500 - Total lineal feet of proposed public streets 500 - Total vehicle trips per day 282 - Traffic Analysis Zone (TAZ) West Ada - Impact Fee Service Area Meridian - Impact Fee Assessment District Locust Grove Road Minor arterial with bike lane designation Traffic count of 1,202 on 2-17-00 (s/o Franklin Road) Better than C — Existing Level of Service Better than C — Existing plus project Level of Service 670 -feet of frontage 50 -feet existing right-of-way (25 -feet from centerline) 96 -feet required right-of-way (48 -feet from centerline) Locust Grove Road is improved with 28 -feet of pavement with no curb, gutter or sidewalk. This segment of Locust Grove Road is listed as "PD" in the District's Five Year Work Program for widening to a 5 -lane street section. Watertower Lane Local/commercial street No traffic count available 58 -feet of frontage 58 -feet required right-of-way for the extension Watertower Lane has been constructed as a 41 -foot street section with curb, gutter and 5 -foot wide concrete sidewalk to the west of the site. Murdoch #2.cnun Page 2 Adkins Drive Local/commercial street No traffic count available 58 -feet of frontage 58 -feet required right-of-way for the extension Adkins Drive has been constructed as a 41 -foot street section with curb, gutter and 5 -foot wide concrete sidewalk to the north of the site. Franklin Road Minor arterial with bike lane designation Traffic count of 10,932 on 5-9-00 (e/o Stratford Drive) Traffic count of 10,896 on 5-9-00 (e/o Locust Grove Road) Better than C — Existing Level of Service Better than C — Existing plus project Level of Service 0 -feet of frontage Franklin Road is improved with two lanes between Eagle Road and Locust Grove Road. Franklin Road is listed in the District's Five Year Work Program for widening to 5 -lanes in 2003 and 2004. B. On February 12, 2001, the District Planning and Development staff inspected this site and evaluated the transportation system in the vicinity. On February 16, 2001, the staff met as the District's Technical Review Committee and reviewed the impacts of this proposed development on the District's transportation system. The results of that analysis constitute the following Facts and Findings and recommended Site Specific Requirements. C. The City of Meridian Planning and Zoning staff is in the process of revising the Comprehensive Plan for the City. The draft plan indicates this area as limited office/light industrial. The current comprehensive plan designation is residential. A police station is allowed in a residential zone. The applicant intends to rezone the property to L -O or I -L if the corresponding changes are made to the comprehensive plan. The applicant does not intend for the uses in this subdivision to be residential. D. On November 21, 2000, staff reviewed MCUP-00-0054, a conditional use application for the police station. A condition of approval for that application was the extension of Watertower Lane through a portion of the site. The extension of the right-of-way created a lot and the City of Meridian required the applicant to plat the entire parcel. A police station is an allowed use within the R-8 zone. The applicant is not proposing to develop the rest of the site until the adoption of the new Meridian Comprehensive Plan that would allow this area to be zoned L -O (limited office). E. On June 2, 1999, the Commission reviewed and approved Dee Jay (since renamed "Murdoch #1"), a 14 -lot commercial/industrial subdivision located to the west of the subject site. As a Murdoch #2.cmm Page 3 condition of approval, that applicant was required to construct Watertower Lane to the subject applicant's west property line. F. On November 17, 1999, the Commission reviewed and approved Woodbridge, a 164 -lot residential subdivision, located on the east side of Locust Grove Road. As a condition of approval, that applicant was required to construct Woodbridge Drive, the main entrance to the subdivision, at a location 700 -feet south of the north property line, which is across from the subject applicant's south property line. G. Adkins Drive is a local/commercial street that abuts the site's north property line, located approximately 700 -feet west of Locust Grove Road. The roadway has been constructed as a 41 - foot street section with curbs, gutters, and sidewalks within 58 -feet of right-of-way. The applicant should be required to extend the roadway into the site as a 40 -foot street section with curb, gutter and 5 -foot wide concrete sidewalk within 58 -feet of right-of-way. H. The subject applicant should be required to extend Watertower Lane into the site at the west property line as a 40 -foot street section with curb, gutter and 5 -foot wide concrete sidewalk within 58 -feet of right-of-way. The applicant is proposing to extend the roadway to Locust Grove Road. Driveways on Watertower Lane should be located a minimum of 50 -feet from public street intersections and constructed 24 to 30 -feet wide. Graveled driveways abutting public streets create maintenance problems due to gravel being tracked onto the roadway. In accordance with past action by the District the applicant should be required to pave the driveways on Watertower Lane their full width and at least 30 -feet into the site beyond the edge of pavement of Watertower Lane. K. The applicant is proposing to construct one shared 30 -foot wide driveway on Locust Grove Road located in alignment with Woodbridge Drive on the east side of Locust Grove Road. District policy requires driveways on Locust Grove Road to align or offset a minimum of 150 -feet from any existing or proposed driveways or streets. The proposed shared driveway location conforms to District policy and should be approved with this application. L. The applicant should provide a recorded cross access easement among the parcels on Locust Grove Road (south of Watertower Lane). M. Graveled driveways abutting public streets create maintenance problems due to gravel being tracked onto the roadway. In accordance with past action by the District the applicant should be required to pave the driveway on Locust Grove Road its full width and at least 30 -feet into the site beyond the edge of pavement of Locust Grove Road and install pavement tapers with 15 -foot radii abutting the existing roadway edge. N. The applicant should be required to construct a 5 -foot wide concrete sidewalk on Locust Grove Road abutting the parcel, located 2 -feet within the new right-of-way. Coordinate the location, elevation and grade of the sidewalk with District staff. Murdoch #2.cmm Page 4 O. Any irrigation facilities should be relocated outside of the right-of-way on Locust Grove Road. P. All utility relocation costs associated with improving street frontages abutting the site should be borne by the developer. Q. Based on development patterns in this area and the resulting traffic generation, staff anticipates that the transportation system will be adequate to accommodate additional traffic generated by this proposed development with the requirements outlined within this report. The following Site Specific Requirements and Standard Requirements must be met or provided for prior to ACHD approval of the final plat: Site Specific Requirements: 1. Dedicate 48 -feet of right-of-way from the centerline of Locust Grove Road abutting the parcel by means of recordation of a final subdivision plat or execution of a warranty deed prior to issuance of a building permit (or other required permits), whichever occurs first. Allow up to 30 business days to process the right-of-way dedication after receipt of all requested material. The owner will be paid the fair market value of the right-of-way dedicated which is an addition to existing ACHD right-of-way. 2. Extend Adkins Drive into the site at the north property line as proposed as a 40 -foot street section with curb, gutter and 5 -foot wide concrete sidewalk within 58 -feet of right-of-way. 3. Extend Watertower Lane into the site at the west property line as proposed as a 40 -foot street section with curb, gutter and 5 -foot wide concrete sidewalk within 58 -feet of right-of-way. 4. Locate driveways on Watertower Lane a minimum of 50 -feet from public street intersections and constructed 24 to 30 -feet wide. 5. Pave the driveways on Watertower Lane their full width and at least 30 -feet into the site beyond the edge of pavement of Watertower Lane. 6. Construct one shared 30 -foot wide driveway on Locust Grove Road located in alignment with Woodbridge Drive on the east side of Locust Grove Road as proposed. Pave the driveway on Locust Grove Road its full width and at least 30 -feet into the site beyond the edge of pavement of Locust Grove Road and install pavement tapers with 15 -foot radii abutting the existing roadway edge. 7. The applicant should provide a recorded cross access easement among the parcels on Locust Grove Road (south of Watertower Lane). Murdoch #2.cmm Page 5 8. Construct a 5 -foot wide concrete sidewalk on Locust Grove Road abutting the parcel, located 2 - feet within the new right-of-way. Coordinate the location, elevation and grade of the sidewalk with District staff. 9. Any irrigation facilities shall be relocated outside of the right-of-way on Locust Grove Road. 10. All utility relocation costs associated with improving street frontages abutting the site shall be borne by the developer. 11. As required by District policy, restrictions on the width, number and locations of driveways, shall be placed on future development of this parcel. 12. Other than the access point and public street specifically approved with this application, direct lot or parcel access to Locust Grove Road is prohibited. Lot access restrictions, as required with this application, shall be stated on the final plat. Standard Requirements: A request for modification, variance or waiver of any requirement or policy outlined herein shall be made in writing to the ACED Planning and Development Supervisor. The request shall specifically identify each requirement to be reconsidered and include a written explanation of why such a requirement would result in a substantial hardship or inequity. The written request shall be submitted to the District no later than 9:00 a.m. on the day scheduled for ACHD Commission action. Those items shall be rescheduled for discussion with the Commission on the next available meeting agenda. Requests submitted to the District after 9:00 a.m. on the day scheduled for Commission action do not provide sufficient time for District staff to remove the item from the consent agenda and report to the Commission regarding the requested modification, variance or waiver. Those items will be acted on by the Commission unless removed from the agenda by the Commission. After ACHD Commission action, any request for reconsideration of the Commission's action shall be made in writing to the Planning and Development Supervisor within six days of the action and shall include a minimum fee of $110.00. The request for reconsideration shall specifically identify each requirement to be reconsidered and include written documentation of data that was not available to the Commission at the time of its original decision. The request for reconsideration will be heard by the District Commission at the next regular meeting of the Commission. If the Commission agrees to reconsider the action, the applicant will be notified of the date and time of the Commission meeting at which the reconsideration will be heard. Payment of applicable road impact fees are required prior to building construction in accordance with Ordinance #193, also known as Ada County Highway District Road Impact Fee Ordinance. Murdoch #2.cmm Page 6 4. All design and construction shall be in accordance with the Ada County Highway District Policy Manual, ISPWC Standards and approved supplements, Construction Services procedures and all applicable ACHD Ordinances unless specifically waived herein. An engineer registered in the State of Idaho shall prepare and certify all improvement plans. 5. The applicant shall submit revised plans for staff approval, prior to issuance of building permit (or other required permits), which incorporates any required design changes. 6. Construction, use and property development shall be in conformance with all applicable requirements of the Ada County Highway District prior to District approval for occupancy. 7. It is the responsibility of the applicant to verify all existing utilities within the right-of-way. Existing utilities damaged by the applicant shall be repaired by the applicant at no cost to ACRD. The applicant shall be required to call DIGLINE (1-800-342-1585) at least two full business days prior to breaking ground within ACHD right-of-way. The applicant shall contact ACHD Traffic Operations 387-6190 in the event any ACHD conduits (spare or filled) are compromised during any phase of construction. Murdoch #2.cmm Page 7 8. No change in the terms and conditions of this approval shall be valid unless they are in writing and signed by the applicant or the applicant's authorized representative and an authorized representative of the Ada County Highway District. The burden shall be upon the applicant to obtain written confirmation of any change from the Ada County Highway District. 9. Any change by the applicant in the planned use of the property which is the subject of this application, shall require the applicant to comply with all rules, regulations, ordinances, plans, or other regulatory and legal restrictions in force at the time the applicant or its successors in interest advises the Highway District of its intent to change the planned use of the subject property unless a waiver/variance of said requirements or other legal relief is granted pursuant to the law in effect at the time the change in use is sought. Conclusion of Law: ACHD requirements are intended to assure that the proposed use/development will not place an undue burden on the existing vehicular and pedestrian transportation system within the vicinity impacted by the proposed development. Should you have any questions or comments, please contact the Planning and Development Division at 387-6170. Submitted by: Commission Action: Planning and Development Staff February 28, 2001 Murdoch #2.cmm Page 8 1Z-19-'06 16:29 !FHOM-SSG 2088885mj2 T-100 F00Zl005 F-735 C. VVNI CR I uvvc:m J 1 RCC I 12-19-'e6 16;29 (FRAM -SSC 2088885uj2 T-100 P0031005 F-735 DESIGN ehConsumer Brands ' Warehouse ouse&Distribution Facility DEVELOPMENT EWatertower St @@@ Meridian, Idaho 12-19-'06 16;29 (FO -SSC 2088885 j2 T-100 P005/005 F-735 j Q 6 o6 Eco Q Tp ,5.- o\ C -rn aOc m U z WO 49 a off. E,+°or t °r E3a5°cc 2o ao gs WL I W 13'mM^ �o.9 I'q, 0 0 I N -`- i �K - YMONZ0MON .-mv6riM2�. 7 AYEYgp 3g3,. l'ON NDisV\106ns line'ONI180NS Q°4e �a, w i o � --ON/aV3g J0 SSVS " _ .L9'499 _ _ _ M,S L_l£•OOS _ _ a-ol,lLso N y '�C ,6S'6£4 'W b e ,6Z FZ ni OVOa 3AOiNO 1sn3Ol'S +� `s F OZ ,pOSZm .80'081 ,Z9'104 •659L£ Ti— I 0052 .°8i9 �mza JpYd 9°e _2 .BO'sOZ IA„S I,1S005 ,Z9'LLInno� ofalojo,O6'L£t � Ie M e i L9'l04 M.S6If.00s Z I O' z ,9099z I 3„6Z,OZ.005 II MI8 o N �•$l IM �i m Iw m w W i I z p Z O cFi _ ,90'SOZ I I v Z — �90N- Qry� tS3o U0 w I WoW W s M N Q O m Q N AVM SNIHOV 'S I - i_ m ,90'9EZ 3 .62,OZ00 S ,w2, m "!I Z 5 p n LLI ! d - min S ° 2 Jp so n I a- tY m Q __ � _ •90'SOZ m " VI b f AI OlS9 h �cP NI .6Z,fiZ 3wi6 " -Of,6Z.00 s I ;,00'999 3 .6f,6Z.00 N R - Ao'sse ¢ Utz 0311V1dNn i off^ of mii L ON N0ISIN08n5 NDDDanM O RC�e e 8 O a Y O Q0] J a rc ✓. E..hm a�g�8d mnn§RN�oJ ann Z'a$o� Ww`N oc� n$�Ea,3$xz $pow ° TCobm 2022s�6MN—� g�«3e ^wm o€E�y�agYto 'o SnY�b _mx T°"rvz° So`w w«Sz°XE°nW a 1-4 8 w A 1` 0�5 � 2 2 ag o - s' neo .000v'� a °oz . F.E , « E of bye Baa r � F o 4 1 °'- ly — - a 9.� Z wz W 4,0�- Z W Q 4 v°o ff n Lia a3LP U i Y a Q e Q a« a 8p S v 16 € m W o g 2 « Cm o S off` a W a3 SU o°H2OIH Ow F p} > a 0 xG�q o as r 3 9 z w a ns9"= v z LL _u oaa a =� Q ke F 3o It ✓. E..hm a�g�8d mnn§RN�oJ ann Z'a$o� Ww`N oc� n$�Ea,3$xz $pow ° TCobm 2022s�6MN—� g�«3e ^wm o€E�y�agYto 'o SnY�b _mx T°"rvz° So`w w«Sz°XE°nW « a 1-4 8 w A 1` 0�5 � 2 2 ag o a °oz E of bye Baa r � F o r ly — - a 9.� Z wz W "� 3 o Z W Q 4 v°o ff n Lia o U i Y a Q e Q off` Jm W a3 F « a 1-4 8 w A 1` 2 2 ag o a °oz E of bye Baa F r ly — O § Q 4 v°o ff n Lia U 1260 E. Watertower Lane Vicinity Map — - 09EPI`aelpuayu. fggea,j uoi nqu;s[Q V osnogaie� s,usmgas - NOI.L7fIH,LSN00 £ spunig zaumsuoO - ? i i 9 IP .11 LLJ as w C9 WviA§s ___ i IIi F i 3 9yy $ 999 g g 3 Y Y 5 JUN 51 d i cy a 54 11 1 y 9 1p p g s ayk Sd 4 _ Y Z 4 i 1 pq Ed zfl h$ ��3= f,s�_ S �3q�g a�€ o,eayy°ss stye k s>Fg°fax #a�' o ed € Q I n m 151 e° I� Y x .. " m om"_ _ 9 9 ___� _ e d r, R p} R R G R A .^. U 1 a .. • n" a z HIM ` zl Uo3�m ¢ 8€ R N K io s Q U RU °e $ ?H I£ ... oR `' gr�� � W9g -� �' �• 4"�S� � $ :sus= x° a- " s ', .,'"sF¢ §g )9gg ,i@gip@ `aya a° 4 gsg4� ` y a 3 g 41 e. dig az i t aka£ $ BY \[xomfl-tfusON(O �! !� \ / IGM LIGHTING 9111®14 14" Wall Director revision 8/01/06 • wdI4.pdff Type: Job: Page: 3 of 5 ti— Electrical Module PMH = Pulse Start Metal 7,70HPS120 Halide MH = Metal Halide HPS = High Pressure 71100HPS208 Sodium PL = Compact Fluorescent ❑ 70HPS240 Trifle Tube IF = Induction Fluorescent 1W Lamp Lamp Line Watts Type Volts 175 MH 277 Lamp and electrical data supplied for reference Puurposes only. All initial men values shown may vary from one manufacturer to another. Consult lamp manufacturer's data for exact lumen and life data. NOTE: For lamp/ballast information outside of the U.S.A. and Canada, please consult your local Kim representative. Cat. Nos. for Electrical Modules available: `150PMH120'70PMH120` 100PMH120' L1125PMH120' C115OPMH1204 U 5OPMH2O8' OPMH2O8 D 100PMH2O8' D 125PMH2O8' D 15OPMH2O8' D 50PMH240' !- 170PMH2404 'L 100PMH240' D 125PMH240' G 15OPMH2404 L 5OPMH277' 70PMH2774 110OPMH27T L� 125PMH27T L 115OPMH2774 I_15OPMH347' 'u70PMH347' J10OPMH347' Ll15OPMH3474 70PMH480'4t =! 10OPMH480'" ❑ 15OPMH480" Lamu ED -17, Clear ED -17, Clear ED -17. Clear r:D-17. Clear ED -17. Clear Socket Medium Base Medium Base lMM 4ium Base Medium Base Medium Base ANSI Ballast M148, M110 M74.i, M98 M140, M90 M150 M142, M102 -142PL120'❑57PL120'' U 175MH120 7,70HPS120 —J 100HPS120 C 150HPS120 142PL208' U 175MH2O8 D 70HPS208 71100HPS208 L 150HPS208 ❑ 42PL240' D 175MH240 ❑ 70HPS240 D 100HPS240 C 150HPS240 D 42PL277' D 175MH277 D 70HPS277 LJ 100HPS277 U 150HPS277 D 175MH347 D 70HPS347 D 100HPS347 D 150HPS347 D 175MH480' D 70HPS4803 U 100HPS480' D 150HPS480' Lamp ED -17, or T6 Clear G-12, ED -17 Clear T6 Clear, ED -17 Clear, -ED-28 Clear ED -17 Clear or E-18 Clear Socket Medium Base G-12 Base, or Medium Base G72 Base, Medium or Mogul Base Medium Base Base, or Mogul Base ANSI Ballast M-57 S-62 S-54 S-55 -142PL120'❑57PL120'' -I60PL120'�' El70PL120'1 D551F120 142PL208' ❑ 57PL208'' U 60PL208'' U 70PL2081= D 551F208 ❑ 42PL240' i 57PL240'' 160PL2401' U 70PL2401' U 551F240 D 42PL277' U 57PL277'•' i 160PL2771' D 70PL2771' D 551F277 Socket I GX24n-4 Base I GX24o-5 Base 12GB-1 Base I GX24a-6 Base I 'Multiple CFL lamp configurations tie, two 42W lamps) are possible with certain optical systems. Consult factory for details. Remote battery pack and test switch available for 57W, 60W, and 70W CFL lamps - consult factory. "EM" option not available with 6.5W CFI., 55W IF, or 85W IF lamps. '480 volt with medium base lamp sockets may require approval by the local building code authority. 'CAUTION: All manufacturers of metal halicle lamps recommend turning them off for 15 minutes once per week when under continuous operation. This will reduce the risk of arc tube rupture at end of life. Also, color temperature may differ between manufacturers of metal halide lamps. See lamp manufacturers' specification sheets. WARNING: Fixtures must be installed and grounded in accordance with national, state and/or local electrical codes. Failure to do so may result in seriouspersonal injury. For lamp/ballast information outside of the U.S.A. and Canada, please consult your local Kim representative. Lamps by others. 02006 KIM LIGHTING INC. • P.O. BOX 60080, CITY OF INDUSTRY, CA 91716-0080 - TEL 626/968-5666 • FAX: 626/369-2695 5608706213 I Schwan's Consumer Brands DESIGN Warehouse & Distribution Facility DEVELOPMENT EWatertowerSt I Meridian, Idaho ~ /§�, ~ /§�, N=--� DESIGN h ConsumerBrands9 Warehouse &Distribution Facilitylily ARE@ ® DEVELOPMENT E Watertower St k Meridian, Idaho b© 3 B DESIGN m_wConsumer s m Warehouse lDistribution Facility DEVELOPMENT EWateftower& PRE -APPLICATION MEETING NOTES DATE: 10— t6 -0(p Applicant(s): r� Mar(selp- Engineeqrt r�,/�Architect/Planner: Staff: no, . Ssti,va . Proposed Development: .Mew di5zb i 6o:Fiore Gen+er ,Gr ScA o0_M't Location: Cors J k to glL- I ) Murdoch Sub . -L Required Applications: CT R Existing Zoning: C -G-1 Proposed Zoning. i -L Comprehensive Plan Designation: flnm m r iaI For Plats Property Size: Number of Units: Dwelling Type: Sewer: Water: Pressurized Irrigation: Street Buffers: Open Space & Micropaths: Landscape Plan: Lot Size & Frontage: Topography: Hydrology. Street System: Pathway System: Other Applications ❑ Annexation Rezone IF 60M1' PY-d A-NW(?MI_WTWP?VqZD ❑ Conditional Use Permit ❑ Variance ❑ Lot Line Adjustment M.k't 6 - plSZ' Y-3 L'�E— (� g ptth1�T11� (� u SAF Comprehensive Plan Amendment rngna.v z"MerL+ q;vyr% C'FmMerci0.I +0 IMdUs: 1'4,1 • Application Checklist Review Other Agencies to Additional Pre -application Conference: Not recommended Recommended Required Anticipated Submission Date: Anticipated Planning & Zoning Date: The information provided during this meetirg is based upon the currant City of Meridian Zoning d� Subdivision Ordinance and applicable Comprehensive Plan and is valid fora mo)7tbs. Any subsequent cbanges to the Zoning or Subdivision Ordinance or Comprehensive Plan may affectyour application. bbr. c1 . L0Ub 11: J''JHM N0. 400 P.2 CITY OF MERIDIAN j k �' Planning Department 660 E. Watertower Ln., Suitc. 202, Meridian, ID 83642 (208)8845333 Phone / (208)888.6854 Fax PRE -APPLICATION MEETING REQUEST FORM L!dw.(&n Preappliration meelmgt are required prior to the submittal of my erpphratim that reyidres a pabh'r beariq Tbu completed form mart be submitted to the Plmming Depart rot ar kwt48 hours Gefareyour reyaesled meeting time. An Awoddte City Platmcr wild ion, firm the mceBnR by eiiberpbone ore -mail. Name: Murdoch (Project.- Warehouse & CMO -y> t,Wi,v,4t_<; .,U ria >I ;ngineets Contact: Di MLIV,&C�h gtlb- 2- t2002-) ID 83702 f -c &G7 FaxNumber, u'� cr u Y Plar 343-3531 Site Information: Location! Lot 9 & 10, Block 1 N1/2 SEI/4 Section 18, Towns ip 3 N, Number of Lots; Total A 2 1.67 Tax Parcel Number(s): Current R5901170010 and R5901170020 Currei Type of Application(s): 1. 0 preliminary Plat (Submit an 8'/1 x 11 version) Amendment 2. Q Conditional Use Permit 3. X Annexation and/or Rezone 4, 2 Planned Unit Development 5. 0 Unified Development Code 6. 0 Comprehensive Plan Amendment 7. ❑ Variance 8_ Q Other (e.g. City Council reviews) Please list all persons who will attend the pre -application meeting: IN= Stainbronn. Jeff fKingMntisek Corona Specific Questions/Issues:-0-wnerxequested intermediate parcel line .ttr ho_mmoved. Dnev this need to transact before Adminigp-reivc Review Annlicarion> ❑ Check here if your proposed development includes a potential public park, pathway, or school. Monday (except Holidays) Wednesday X 10:30 12:45 11:15 1:15 2:00 2:45 **We strongly suggest that you bring a conceptual layout of the proposed project to the meeting. Otherwise, staff may require additional pr.e-a lication meetings.** For SmffIIse ORµ; Norify affected ageney, if applicable. ITD (Sue Sullivan, 334-8955) _ MDC (Clair Bowman, 484-4414) —MID 'ch Green, $98-5500 PRE-APP'l, CATION MEETING NOTES DATE: 10- 16-00 Applicants): M&riRkr Engineer/Architect/Planner.Jef( Ki"! Vane &•9Unb n ' Flu Gi Staff: raa_ . Proposed Development: Me,,o dicrM6arm M4er .,Gy S waaws Location: La i-5 1s -Io, B g k- { p—M a 6ri oe to Sub Z. Required Applications: CPA Existing Zoning: C,-61 Proposed Zoning. t -L Comprehensive Plan Designation: C&nm ry er-ao. I For Plats Property Size: Number of Units: Dwelling Type: Sewer: Water: Pressurized Irrigation: Street Buffers: Open Space & Micropaths: Landscape Plan: Lot Size & Frontage: Topography: Hydrology: Street System: Pathway System: Other Applications ❑ Annexation r� Rezone (orif' K4<I0 ❑ Conditional Use Permit ❑ Variance I ❑ Lot Line Adjustment Mit - - Comprehensive Plan Amendment ma p ech rP_AA terL4-FyisyP • Application Checklist Review Other Agencies to Additional Pre -application Conference: Not recom,mended Recommended Required Anticipated Submission Date: Anticipated Planning & Zoning Date: The information provided during this meeting is based srpon the current City of Meridian Zoning & Subdivision Ordinance and alplicable Cot*rehensive Plan and is vah'd for 3 montbs. Any subsegsrent cbanges to the Zoning or Subdivision Ordinance or Coi*mhensive Plan may affectyour a0P§cation. ✓!1 BOLLMAN nr LPEGRAM I -L RUT R1 RUT RUT _t_ ''BOLLMAN.' _r_ I l )GE f° I PRATT L. { tv"ed. eler. Planning Department CERTIFICATE OF ZONING COMPLIANCE Application Checklist Project name: Schwan's Consumer Brands Warehouse and Distribution Facility File #: Applicant/agent: CTA Architects Engineers All applications are required to contain one copy of the following unless otherwise noted: Applicant Staff � Description � X Completed & signed Administrative Review Application Narrative fully describing the proposed use of the property, including the following: X ➢ Information on any previous approvals or requirements for the requested use i.e., applicable conditions of ap2roval or Development Agreement) X Recorded warranty deed for the subject property X Affidavit of Legal Interest signed & notarized by the property owner (If owner is a corporation,. submit a copy of the Articles of Incorporation or other evidence to show that the person signing is an authorized agent. X Scaled vicint map showing the location of the subject property X Sanitary Service Company approval for trash enclosure & access drive (stamped site plan) X A photometric test report for any light fixture(s) with a maximum output of 1,800 lumens or more see UDC 11-3A-11 X Copy of the recorded plat that the property lies within 8 r/2" x 11" X Address verification letter from Public Works See Tricia Bieren 898-5500 d' X Site Plan -4 copies (folded to 8 Y:" x 11" size) The following items must be shown on the siteplan: X • Date, scale, north arrow, and project name (scale not less than 1"=50') • Names, addresses, and telephone numbers of the developer and the person and/or X firm preparing the plan X Parking stalls and drive aisles X • Trash enclosures location X • Detail of trash enclosure must be screened on 3 sides X • Location and specifications for underground irrigation (pressurized irrigation can only be waived if you prove no water rights exist to subject property) _ X Y Sidewalks or pathways (proposed and existing) X • Location -of proposed building on lot (include dimensions to property lines) �.---- X • Feneill (proposed and existing) • Calculations table including the following: Number of parking stalls required & provided (specify handicap & compact stalls) X ➢ Building size (sq. ft.) ➢ Lot size (sq, ft.) ➢ Setbacks ➢ Zoning district X • Reduction of the site plan 8 %" x 11" Landscape plan— 3 copies (folded to 8'/z" x 11" size) Plat must have a scale no smaller than I " = 50'(1 " = 20' is preferred) and be on a standard X drawing sheet, not to exceed 36"x 48" (24"x 36" is preferred). A plai which carrot be drama m -•-"" its entirety, on a single sheet must be drawn ivith appropriate match lines on two or more sheets. The following items must be included on the landscapeplan: X _ Date, scale, north arrow, and project name X • Names, addresses, and telephone numbers of the developer and the person and or firm preparing the plan 660 E. Watertower Lane, Suite 202 • Meridian, Idaho 83642 Phone: (208) 884-5533 • Facsimile: (208) 888-6854 • Website: www.meridiancity.org q[r(� X i Existing natural features such as canals, creeks, drains, ponds, wetlands, flood Tains, high groundwater areas, and rock outcroppings, � , X • Location, size, and species of all existing trees on site with trunks 4 inches or greater in diameter, measured 6 inches above the ground. Indicate whether the tree will be retained or removed. X e A statement of how existing healthy trees proposed to be retained will be protected from damage during construction Y Existing structures, planting areas, light poles, power poles, walls, fences, berms, X parking and loading areas, vehicular drives, trash areas, sidewalks, pathways, stormwater detention areas, signs, street furniture, and other man-made elements. X • Existing and proposed contours for all areas steeper than 20% slope. Berms shall be shown with one -foot contours. X Y Sight Triangles as defined in 11-3A-5 of this ordinance. 6 Location and labels for all proposed plants, including trees, shrubs, and X grOundCovers (trees must not be planted in City water or sewer easements). Scale shown for plant materials shall reflect approximate mature size • A plant list that shows the plant symbol, quantity, botanical name, common name, X minimum planting size and container, tree class (I, II, or III), and comments (for spacing, stakin , and installation as appropriate). X • Planting and installation details as necessary to ensure conformance with all required standards. X • Design drawing(s) of all fencing proposed for s creening purposes • Calculations of project components to demonstrate compliance with the requirements of this ordinance, including: ➢ Number of street trees and lineal feet of street frontage ➢ Width of street buffers (exclusive of right-of-way) X ➢ Width of parking lot perimeter landscape strip ➢ Buffer width between different land uses (if applicable) ➢ Number of parking stalls and percent of parking area with internal landscaping ➢ Total number of trees and tree species mix ➢ Mitigation for removal of existing trees, including number of caliper inches being removed X Reduction of the landsca e plan 8 %" x 11" X BuildhIg elevations showing construction materials _ X If applying for approval of a public school, provide additional information as required by the Public School Facility supplemental checklist per §67-6519. Fee f this project had prior approval on a site plan, reduced fees may apply) ACHD Acce Mance: Applicant shall be responsible for meeting the requirements ofACHD as they pertain to this application. All impactfees, ifany, shall be paid prior to the issuance ofa buildingpennit. Ifany changes must be made to the site plan to accommodate the ACHD requirements, a new siteplan shall be submitted to the City of Meridian Planning & Zoning Departmentfor approval prior to the issuance ofa buildingpenniG Your buildingpennit will not be issued until ACHD has approvedyourplans and all associatedfees have been paid. THIS APPLICATION SHALL NOT BE CONSIDERED COMPLETE UNTIL STAFF HAS RECEIVED ALL REQUIRED INFORMATION 660 E. Watertower Lane, Suite 202 • Meridian, Idaho 83642 Phone: (208) 884-5533 • Facsimile: (208) 888-6854 • Website: www.meridiancity.org (Rev. 9121106) 01� PLANNING & ZONING DEPARTMENT INSPECTION CHECKLIST COMMERCIAL/CZC SITES This checklist should be attached to the inside cover of the CZC file at ALL times. Planner/Inspector Name: Project Name: Contractor/Company Name: CZC File No.: Phone No.: First Inspection Date: Second Inspection Date: Third Inspection Date: / / (NOTE: If a third inspection is required, a fee of $60 must be submitted to theP&Z Dept. be ore the inspection is done) Landscape Plan Checklist Item Site Notes O.K. r t bate oiappxovedlandsaaerlyfi' r ,% w 15, $ rStreetbuffer/PeXunefe3$lBtiferUeiYieen]a!ine „,.::, x. j tt.,; z`.NW.,+}' °. 1. Width ofbuffer (exclude detacheds/w widths 2. # of trees 3. Caliper/size of trees (measure 6-8 inches above ound) 4. Species mix per plan S. Groundcover (ifseeded, verify ermination) 6. Right-of-way landscaping 7. Verify no encroachments (e.g. fencing, asking) 8. Be rm.ng (max. 2,1 slope; 3:1 i IawnJ -P N 1. 1. Verify min. 5' b/w curbs 2. Verify mEner50 sq. ft. 3. Plantingplan D. Exis* trees/mitigation 1. Verify existing tree(s) retained r- 2. Verify mitigation trees) planted ��j- Ret: J.,? }/i ) s:--�P<�Z!13radiP�$Z.�fta«tir�P2parnn<v:! Po!ec;�c E. Sight triangle(s) 1. Verify size/location O.K. Date of appidved site plat ! / £ „' -- 2. Verify height of shrubs 1. Standard stall dimensions F. Pressurized irrigation (verify installed) G. Stounwater area(s) 1. Less than 3:1 slopes 2. Dry creels formation (if applicable) 3. Max. 5 ft. dimension for rock sum 4. Max. 2 ft. dimension for sand/grease grates Site Plan Checldist Rev. 5:25.-05 ;:!P&ZBrvItPdZAdnrr Dep, rnrenspolicies Item Site Notes O.K. Date of appidved site plat ! / £ „' -- 1. Standard stall dimensions 2. Compact stall dimensions 3. Handicap stall dimensions 4. Handicap signs/striping 5. Aisle width 6. Wheel stops (if required) G. T rd nclosnre f 1. Min. 3 -sided screening 2. Constructed per plan 1. Verify location 2. Verify minimum width E. Curbing 1. Installed per plan F. Special conditions/Redlines , , 1. Verify any special conditions from CZC or redline notes on plan are Complete Rev. 5:25.-05 ;:!P&ZBrvItPdZAdnrr Dep, rnrenspolicies Post -Inspection Checklist A, Inco aplete? (Follow 5 steps below) 1. Obtain bid for incomplete improvements + 110% 2. Ownerlcontractor posts surety (cash, check or Letter of Credit) 3. Clearly print # of days the "Temp. CO" is valid on card 4. Sign "Temporary" column on CO card 5.8 u b nu t check or Letter of Credit to Finance Dept. with memo 1. Sign and date "Final' column on CO card 2. Notify Finance Dept. to release surety (if it was a Temporary CO) 1 2. Complete checldist and close file I -I * The only instance that a CO may be released prior to 100% completion of improvement is inclement weather, as determined by the Director. If weather is a factor, follow MCC 12-13-19-2. Xer. 5,,f25,,IuU s: 4Pt4Xti3;;;:ilP«ZAsfi.v'rI )nparnr: 7u Polici,—,'