A201_BUILDING ELEVATIONSLEVEL 10' -0"TOP OF CONCRETE20' -0"45321FINISH FLOOR0' -0"30'-0"30'-0"36'-0"36'-0"72'-0"60'-0"132'-0"1231011165810181711TYPINSET HEIGHT9' -0"TOP OF CONCRETE20' -0"B8ABCDEFGHIFINISH FLOOR0' -0"240'-0"70'-0"310'-0"38'-9"38'-9"38'-9"38'-9"38'-9"38'-9"7'-6"31'-3"38'-9"2310119118511982110'-0"181720581951651112212519UUU231011TYP418INSET HEIGHT9' -0"TOP OF CONCRETE20' -0"ABCDEFGHIFINISH FLOOR0' -0"310'-0"38'-9"38'-9"38'-9"38'-9"38'-9"38'-9"38'-9"38'-9"20'-0"72'-7 1/2"47'-3"30'-3"47'-3"30'-3"47'-3"15'-1 1/2"61011059111101195756916111015859511142310444V2323TYPTYP4101INSET HEIGHT9' -0"TOP OF CONCRETE20' -0"45321FINISH FLOOR0' -0"132'-0"30'-0"30'-0"36'-0"36'-0"30'-0"2'-0"34'-0"30'-0"4'-0"32'-0"SS131111115923104112651466VV194INSET HEIGHT9' -0"3449654321ABCDEABCDE654321REVISIONSArchitects and Planners, Chartered408 E. Parkcenter Blvd, Suite 205, Boise Idaho 83706DATE:PROJECT NO:SHEET:C:\Users\rebecca\Documents\1945 KENDALL R19_rebecca9D32Y.rvtA-201BUILDING ELEVATIONS1945KENDALL AUTO GROUP HEADQUARTERSTENANT IMPROVEMENTS07/01/20203449 E. COPPER POINT DRIVE MERIDIAN, IDAHO 836423/32" = 1'-0"A-201B4SOUTH BUILDING ELEVATION3/32" = 1'-0"A-201C1EAST BUILDING ELEVATION3/32" = 1'-0"A-201A1WEST BUILDING ELEVATION3/32" = 1'-0"A-201B1NORTH BUILDING ELEVATIONKEYNOTES1 EXISTING CONCRETE WALL PANEL. PREP, PRIME, AND PAINT PER "FACADE REPAIR AND REFINISH"NOTES. COLOR 1 WITH COLOR 2 ACCENT BAND.2 EXISTING "DRIVIT" CORNICE. PREP, PRIME, AND PAINT PER "FACADE REPAIR AND REFINISH"NOTES. COLOR 33 EXISTING SHEET METAL CORNICE CAP. PREP, PRIME, AND PAINT PER "FACADE REPAIR ANDREFINISH" NOTES. COLOR 34 EXISTING CONCRETE COLUMN. PREP, PRIME AND PAINT PER "FACADE REPAIR AND REFINISH"NOTES. COLOR 1 WITH COLOR 4 ACCENT.5 EXISTING ALUMINUM STOREFRONT ENTRY DOORS, MULLIONS, AND GLAZING6 INFILL EXISTING OPENING WITH STOREFRONT MULLION AND GLAZING TO MATCH ADJACENT7 RECONFIGURE EXISTING OPENING FOR SIDELIGHT ON HINGE SIDE OF DOOR. REUSE SAVEDEXISTING DOOR.8 EXISTING HOLLOW METAL DOOR AND FRAME TO REMAIN. PREP, PRIME, AND PAINT PER "FACADEREPAIR AND REFINISH" NOTES.9 EXISTING METAL SOFFIT PANELS TO BE CLEANED AND REPAINTED10 REPLACE ALL EXISTING LIGHT FIXTURES PER ELECTRICAL11 REMOVE EXISTING SEALANT AND BACKER ROD FROM ALL CONCRETE WALL PANEL JOINTS.INSTALL NEW BACKER ROD AND SEALANT PER "FACADE REPAIR AND REFINISH" NOTES. TYPICAL.12 INFILL OPENING WITH EXISTING, RELOCATED STOREFRONT MULLION, DOOR, AND SIDELIGHT13 NEW ALUMINUM STOREFRONT WINDOW CUT INTO CONCRETE WALL PANEL. ALUMINUM FRAMINGTO MATCH PROFILE AND FINISH OF EXISTING, REFER TO STRUCTURAL14 ILLUMINATED SIGNAGE BY OTHERS. SEE ELECTRICAL FOR ROUGH-IN15 NON-ILLUMINATED SIGNAGE BY OTHERS.16 NEW FULL GLASS HOLLOW METAL DOOR IN EXISTING FRAME17 CONCRETE COLUMN PIER, PER STRUCTURAL AND C6/A-10218 PRE-FINISHED ALUMINUM PATIO COVER BY OTHERS (SEPARATE SUBMITTAL). SEE A-102.19 NEW STOREFRONT ALUMINUM FRAME OVER EXISTING CONCRETE FILLED HOLLOW METAL DOORFRAME. ALUMINUM FINISH AND INSUALTED GLASS TO MATCH EXISTING STOREFRONT20 NEW OVERHEAD COILING DOOR IN EXISTING STOREFRONT OPENING.21 NEW WALL MOUNTED LIGHTS PER ELECTRICAL.22 EXISTING DOOR AND FRAME. NO ACCESS. REMOVE HARDWARE23 EXISTING BIKE RACKFACADE REPAIR AND REFINISHPREPARATION AND PRIMING:• POWER WASH ENTIRE FACADE, INCLUDING METAL SOFFIT PANELS• SAND PREP ALL AREAS OF BARE CONCRETE TO FEATHER EDGE REMAINING PAINT• SAND ALL AREAS OF HAIRLINE CRACKING. WIRE BRUSH TO REMOVE LOOSE MATERIAL• CRACKS 1/16" AND WIDER: WIDEN THE CRACK USING A CHISEL AND HAMMER OR DREMEL TOOL TO A MINIMUM OF 1/8". BREAK AWAY ANY DETERIORATING CONCRETE. REMOVE LOOSE MATERIAL WITH A STIFF WIRE BRUSH.• FILL CRACKS (HAIRLINE AND WIDER) WITH CTS CEMENT "RAPID SET WUNDERFIXX". SAND REPAIRED AREAS TO A SMOOTH FINISH AND UNIFORM APPEARANCE.• REMOVE ALL SEALANT AND BACKER ROD FROM ALL TILT-UP PANEL JOINTS.• PRIME ALL CONCRETE AND DRIVIT SURFACES WITH SHERWIN WILLIAMS "LOXON CONDITIONER WHITE #LX03W0100• SAND ALL RUST AND DETERIATED PAINT FROM HOLLOW METAL DOORS AND FRAMES AND SPOT PRIME WITH SHERWIN WILLIAMS "PROCRYL METAL PRIMER" #B66W01310FINISH COATING AND PAINTING:• CONCRETE PANELS: 1-COAT SHERWIN WILLIAMS "CONFLUX SHERLASTIC ELASTOMERIC" #CF16W0051• DRIVIT CORNICES: 1-COAT SHERWIN WILLIAMS "A-100 EXTERIOR LATEX, FLAT" #A06W00211• METAL SOFFIT PANELS: 2-COATS "BOND-PLEX WATERBASED ACRYLIC COATING" #B71W00211• HOLLOW METAL DOOR AND FRAMES: 2-COATS "PRO INDUSTRIAL DTM ACRYLIC", SEMI-GLOSS, #B66W01151• SHEET METAL PARAPET CAP: 2-COATS "PRO-INDUSTRIAL DTM ACRYLIC", SEMI-GLOSS, #B66W01151• ALL OTHER PREVIOUSLY PAINTED STEEL: PREP AND REPAINT SAME AS HOLLOW METAL DOORSCONCRETE WALL PANEL JOINTS• INSTALL NEW BACKER ROD AND SEAL WITH BASF "MASTERSEAL NP 2" POLYURETHANE SEALANT OR EQUAL. COLOR AS SELECTED BY ARCHITECT.