Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
A111 - COMPOSITE ROOF PLAN
A A 11 1212 B B C C D D E E F F G G H H J J 22 33 44 55 1010 66 77 88 99AREA 'A'AREA 'B'1/A1121/A113AREA 'B'AREA 'C'1/A1131/A114AREA 'D'AREA 'E'1/A1151/A116AREA 'E'AREA 'F'1/A1161/A117AREA 'A' AREA 'D' 1/A112 1/A115 AREA 'C' AREA 'F' 1/A114 1/A117 A203 1 580'-0" 72'-6"72'-6"72'-6"72'-6"72'-6"72'-6"72'-6"72'-6"360'-0"12'-0"24'-0"36'-0"36'-0"36'-0"36'-0"36'-0"36'-0"36'-0"36'-0"36'-0"1111 1 A301 ______________ 1 A301 ______________ 2 A301 ______________ 2 A301 ______________ 3 A301 ______________3 A301 ______________ 4 A301 ______________4 A301 ______________ SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPESLOPERIDGESLOPESLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPE SLOPERIDGESLOPESLOPERIDGESLOPESLOPERIDGESLOPE SLOPERIDGESLOPEA2041 A201 1 A2021 A. SEE STRUCTURAL DRAWINGS FOR ROOF DECK HEIGHTS TO ESTABLISH ROOF SLOPES AND ROOF MEMBER LOCATIONS. B. COORDINATE WITH ELECTRICAL, MECHANICAL AND PLUMBING DRAWINGS FOR ADDITIONAL INFORMATION ON ROOF PENETRATIONS. C. ALL FINISHED ROOF SLOPES TO ACHIEVE A MINIMUM OF 1/4" PER FOOT SLOPE (UNLESS NOTED OTHERWISE) IN DIRECTION INDICATED. IT IS THE RESPONSIBILITY OF THE ROOFING CONTRACTOR TO INSTALL ROOFING COMPONENTS TO MEET THESE REQUIREMENTS. D. ALL ROOF MEMBRANE ACCESSORIES SHALL COME FROM THE SAME MANUFACTURER OR FROM A SUPPLIER APPROVED BY THE MEMBRANE MANUFACTURER. ALL ROOF COVERING, MATERIAL AND ACCESSORIES SHALL BE COMPATIBLE. E. ALL TAPERED CRICKETS TO BE PER MANUFACTURERS RECOMMENDATIONS TO PROVIDE POSITIVE DRAINAGE TO ROOF DRAIN. F. ALL DIMENSIONS ARE FOR GENERAL ARRANGEMENT AND LOCATION ONLY. ACTUAL REQUIREMENTS AND DIMENSIONS ARE TO BE VERIFIED AND COORDINATED WITH EQUIPMENT, OTHER CONSTRUCTION TRADES, SHOP DRAWINGS AND STRUCTURAL FRAMING. G. ALL ROOF TOP CONDUIT, GAS LINES, ETC. SHALL BE SUPPORTED WITH PRE-MANUFACTURED SUPPORTS. H. ALL RUNS OF ELECTRICAL CONDUIT, GAS LINES, COMMUNICATION CABLE, ETC. ACROSS THE ROOF AREAS OR ALONG ROOF PARAPETS ARE NOT SHOWN ON ROOF PLANS. CONTRACTOR SHALL VERIFY LOCATION AND QUANTITY WITH OTHER TRADES. I. CONSTRUCTION SHALL BE IN FULL COMPLIANCE WITH ALL CURRENT LOCAL CODES AND REGULATIONS IN EFFECT AT THE TIME OF AGREEMENT BETWEEN OWNER AND CONTRACTOR. J. DETAILS IN THE PROJECT DRAWINGS ARE SHOWN AT SPECIFIC LOCATIONS AND ARE INTENDED TO SHOW GENERAL REQUIREMENTS THROUGHOUT. K. DETAILS NOTED ARE “TYPICAL” AND IMPLY ALL SIMILAR CONDITIONS ARE TO BE TREATED SIMILARLY. MODIFICATIONS MADE BY THE CONTRACTOR TO ACCOMMODATE MINOR VARIATIONS WILL BE DONE WITHOUT ADDITIONAL COST TO THE OWNER. GENERAL NOTES ROOF PLAN LEGEND SHEET WORK NOTE 1 A101 SIM DETAIL OR SECTION NUMBER SHEET WHERE DRAWN X DIMENSION TO FACE OF FRAMING OR CENTER LINE OF OPENING X"/1-0"INDICATES ROOF SLOPE DIMENSION TO GRID LINE ROOF DRAIN ELEVATION, SEE PLANX'-XX" T.O.W. TOP OF WALL TAPERED CRICKETS / INSULATION INSTALL PER MANUFACTURERS SPECIFICATIONS TO PROVIDE POSITIVE DRAINAGE TO ROOF DRAIN REVISIONS 10/7/2020 8:35:44 AM COMPOSITE ROOF PLAN A111 10.07.2020 © 2020 | ALL RIGHTS RESERVED PERMIT DOCUMENTS DESIGNED BY | YATES DRAWN BY | SCANLIN HICKORY WAREHOUSEH.O.T.2 LLLP1021 N Hickory Ave, Meridian, Idaho 83642 | Project# HOT2_YANKEWH | L:\HOT2_YANKEWH\BIMCAD\Revit\HOT2_YANKEWH_arch19.rvt PROJECT# | HOT2_YANKEWH TRUE NORTHPLAN NORTH 3/64" = 1'-0"A111 1 COMPOSITE ROOF PLAN AREA 'A' AREA 'B' AREA 'C' AREA KEY PLAN AREA 'D' AREA 'E' AREA 'F' 2 2 09.25.2020 ADDENDUM #2 JOSHUA MICHAEL HERSEL STATE OF IDAHO AR-985248 ARCHITECT LICENSED 10/07/2020 TYPICAL SKYLIGHTS TYPICAL SKYLIGHTS